Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053728 POWER DISTRIBUTION _0261028 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Do not remove the main body ECU (multiplex network body ECU) except when replacing it.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.DISCONNECT DISCHARGE DOOR CONTROL BATTERY AND DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Door Control Battery)

HINT:
·

When the door control battery becomes completely discharged and the power supply is cut, the multiplex network body ECU (main body ECU) communication lost error "Lost communication with vehicle" appears on the GTS display.

·

The number of times the Active Test can be performed depends on the charge condition of the door control battery.



CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Make sure to perform this procedure with the power supply of the battery and door control battery cut to prevent damage during removal and installation of the instrument panel junction block assembly.

·

Make sure to perform the following procedures, and then perform removal and installation of the instrument panel junction block assembly with the power supply from the battery and door control battery cut.



a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.

Body Electrical / Main Body / Active Test
Tester Display Control Range
Shock Detection Unlock UNLOCK/LOCK

NOTICE:

Do not perform the Active Test at this time.



e.

Disconnect the cable from the negative (-) battery terminal.


f.

Repeat the "Shock Detection Unlock" Active Test until the multiplex network body ECU (main body ECU) communication lost error "Lost communication with vehicle" appears on the GTS display.

Body Electrical / Main Body / Active Test
Tester Display
Shock Detection Unlock

HINT:
·

When the door control battery becomes completely discharged and the power supply is cut, the multiplex network body ECU (main body ECU) communication lost error "Lost communication with vehicle" appears on the GTS display.

·

The number of times the Active Test can be performed depends on the charge condition of the door control battery.




Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/o Door Control Battery)

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 58191 3.REMOVE FRONT FLOOR FOOTREST (for LHD)

Hide 67920 4.REMOVE DOOR SCUFF PLATE ASSEMBLY LH

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

Hide 55606 6.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62312B 7.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 55318C 8.REMOVE INSTRUMENT SIDE PANEL LH

Hide 55045 9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 73900 10.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 11.REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD, except 5L-E)

a.
E376834C01
0,0 0,0 false
V100135

Connector (A)
V100136

Connector (B)


for Type A:

i.

Disconnect the 2 connectors (A) and connector (B).



b.

for Type B:

i.

Disconnect the 2 connectors (A).



c.
E376835C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector (A)
V100137

Connector (B)
V100155

Protective Tape


Disconnect the 2 connectors (A).


d.

w/ Door Control Battery:

i.

Disconnect the connector (B).



e.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.


f.
E376836C01
0,0 0,0 false
V100135

Nut (A)
V100136

Nut (B)


Remove the 2 nuts (A).


g.

w/ Door Control Battery:

i.

Remove the 2 nuts (A) and nut (B).



h.
E376828

Detach the clamp.


i.
E376829

Detach the clamp.


j.
E376830

Detach the clamp.


k.
E376840C01
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector.


l.
E376841C01
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector and then remove the driver side junction block assembly with the main body ECU.


Hide 12.REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD, 5L-E)

a.
E376831

Disconnect the 3 connectors.


b.
E376832C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector
V100155

Protective Tape


Disconnect the connector.


c.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.


d.
E376833

Remove the 2 nuts.


e.
E376828

Detach the clamp.


f.
E376829

Detach the clamp.


g.
E376830

Detach the clamp.


h.
E376837C01
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector.


i.
E376838

Detach the claw and release the connector's lock as shown in the illustration.


j.
E376839C01
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector and then remove the driver side junction block assembly with the main body ECU.


Hide 13.REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD, except 5L-E)

a.
E376863C01
0,0 0,0 false
V100135

Connector (A)
V100136

Connector (B)


for Type A:

i.

Disconnect the 2 connectors (A) and connector (B).



b.

for Type B:

i.

Disconnect the 2 connectors (A).



c.
E376890C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector
V100155

Protective Tape


Disconnect the 2 connectors.


d.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.


e.
E376891C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector
V100155

Protective Tape


Disconnect the 2 connectors.


f.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector.


g.

Detach the clamp.


h.
E376892

Remove the 2 nuts.


i.

Detach the 4 clamps.


j.

w/ KDSS:

i.

Remove the stabilizer control ECU.

Click hereSuspension>SUSPENSION CONTROL>STABILIZER CONTROL ECU>REMOVAL



k.
E376893

Detach the clamp.


l.
E376894

Detach the clamp.


m.
E376899C01
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector.


n.
E376900C01
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector and then remove the driver side junction block assembly with the main body ECU.


Hide 14.REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD, 5L-E)

a.
E376862

Disconnect the 3 connectors.


b.
E376889C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector
V100155

Protective Tape


Disconnect the connector.


c.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.


d.
E376891C01
0,0 0,0 false
V100135

Lever Connector
V100136

Connector
V100155

Protective Tape


Disconnect the 2 connectors.


e.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector.


f.

Detach the clamp.


g.
E376892

Remove the 2 nuts.


h.

Detach the 4 clamps.


i.
E376893

Detach the clamp.


j.
E376894

Detach the clamp.


k.
E376910C01
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector.


l.
E376897

Detach the claw and release the connector's lock as shown in the illustration.


m.
E376898C01
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the lever connector and then remove the driver side junction block assembly with the main body ECU.


Hide 8598A 15.REMOVE DOOR CONTROL BATTERY (w/ Door Control Battery)

Hide 16.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E378112C01
0.083,0.083 0.542,0.521 0.458,0.438 12 false *A 0.083,2.427 0.542,2.865 0.458,0.438 12 false *B
*A for LHD
*B for RHD


Remove the bolt.


b.

Detach the guide and remove the wiring harness clamp bracket.


c.
E183106C08
0.521,3.042 0.448,2.427 true 0.198,2.76 0.333,2.365 true 0.094,2.781 0.26,2.958 0.167,0.177 10 false *1 0.458,3.052 0.625,3.229 0.167,0.177 10 false *2
*1 Main Body ECU (Multiplex Network Body ECU)
*2 Driver Side Junction Block Assembly
V100155

Protective Tape


Press the claw of the driver side junction block assembly as shown in the illustration to release the lock.


d.

With the driver side junction block assembly lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the main body ECU (multiplex network body ECU) and driver side junction block assembly.

NOTICE:
·

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

·

Do not insert the screwdriver under the connector socket of the driver side junction block assembly or the main body ECU (multiplex network body ECU).




e.
E183107C01
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.

NOTICE:
·

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).

·

Replace the driver side junction block assembly or the main body ECU (multiplex network body ECU) when the connector terminal, locking section or case is damaged or deformed.




f.
B195950C01
0.885,0.313 1.323,0.156 1.323,0.156 0.99,0.406 true 0.635,0.688 0.917,0.896 0.281,0.208 10 false (1) 1.646,1.219 1.927,1.448 0.281,0.229 10 false (2) 1.333,0.042 1.698,0.313 0.365,0.271 10 false *a
*a Rib


Catch hold rib of ECU's lock and raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.

NOTICE:
·

Do not touch the driver side junction block assembly connector or the main body ECU (multiplex network body ECU) connector.

·

When removing the driver side junction block assembly or the main body ECU (multiplex network body ECU), take care not to damage it.

·

Do not use the driver side junction block assembly or the main body ECU (multiplex network body ECU) that has been dropped or subjected to a strong shock.