Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › COMBINATION SWITCH › from 2017.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0326217 COMBINATION SWITCH G

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84970 1.INSPECT COMBINATION SWITCH ASSEMBLY (w/ Module Switch (2nd Start))

a.
C380114C01
2.479,1.781 2.479,1.344 true 0.792,1.781 0.792,1.344 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 2.365,1.813 2.719,2.021 0.354,0.208 10 false 2ND 0.76,1.802 0.917,2 0.156,0.198 10 false E
*a Component without harness connected
(Combination Switch Assembly (w/ Module Switch (2nd Start)))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
14 (2ND) - 24 (E) Combination switch (2nd Start) pushed and held Below 1 Ω
Combination switch (2nd Start) not pushed 10 kΩ or higher


If the result is not as specified, replace the combination switch assembly (w/ Module Switch (2nd Start)).


b.
C380114C02
2.646,1.781 2.646,1.344 true 1.198,0.333 1.031,0.333 1.031,0.333 0.781,1.031 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 2.563,1.813 2.906,2.01 0.344,0.198 10 false ILL+ 1.24,0.271 1.583,0.469 0.344,0.198 10 false ILL-
*a Component without harness connected
(Combination Switch Assembly (w/ Module Switch (2nd Start)))


Apply battery voltage between the terminals of the combination switch assembly (w/ Module Switch (2nd Start)), and check the illumination condition of the combination switch assembly (w/ Module Switch (2nd Start)).

OK:
Measurement Condition Specified Condition
Battery positive (+) → 13 (ILL+)
Battery negative (-) → 12 (ILL-)
Illuminates


If the result is not as specified, replace the combination switch assembly (w/ Module Switch (2nd Start)).


Hide 84720J 2.INSPECT PATTERN SELECT SWITCH ASSEMBLY (w/o Module Switch (2nd Start))

a.
C380113C01
2.063,1.865 2.063,1.313 true 1.375,1.865 1.375,1.313 true 1.26,1.896 1.604,2.104 0.344,0.208 10 false 2ND 2.042,1.885 2.198,2.083 0.156,0.198 10 false E 0.042,0.042 0.313,0.292 0.271,0.25 10 false *a
*a Component without harness connected
(Pattern Select Switch Assembly (w/o Module Switch (2nd Start)))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (2ND) - 2 (E) Pattern select switch (2nd Start) pushed and held Below 1 Ω
Pattern select switch (2nd Start) not pushed 10 kΩ or higher


If the result is not as specified, replace the pattern select switch assembly (w/o Module Switch (2nd Start)).


b.
C380113C02
2.281,1.865 2.281,1.313 true 1.146,1.865 1.146,1.313 true 1.052,1.896 1.375,2.104 0.323,0.208 10 false ILL+ 2.188,1.885 2.531,2.094 0.344,0.208 10 false ILL- 0.042,0.031 0.302,0.281 0.26,0.25 10 false *a
*a Component without harness connected
(Pattern Select Switch Assembly (w/o Module Switch (2nd Start)))


Apply battery voltage between the terminals of the pattern select switch assembly (w/o Module Switch (2nd Start)), and check the illumination condition of the pattern select switch assembly (w/o Module Switch (2nd Start)).

OK:
Measurement Condition Specified Condition
Battery positive (+) → 6 (ILL+)
Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the pattern select switch assembly (w/o Module Switch (2nd Start)).


Hide 84970E 3.INSPECT NO. 2 COMBINATION SWITCH ASSEMBLY (w/o Module Switch (2nd Start))

a.
C380114C01
2.479,1.781 2.479,1.344 true 0.792,1.781 0.792,1.344 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 2.365,1.813 2.719,2.021 0.354,0.208 10 false 2ND 0.76,1.802 0.917,2 0.156,0.198 10 false E
*a Component without harness connected
(No. 2 Combination Switch Assembly (w/o Module Switch (2nd Start)))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
14 (2ND) - 24 (E) No. 2 combination switch (2nd Start) pushed and held Below 1 Ω
No. 2 combination switch (2nd Start) not pushed 10 kΩ or higher


If the result is not as specified, replace the No. 2 combination switch assembly (w/o Module Switch (2nd Start)).


b.
C380114C02
2.646,1.781 2.646,1.344 true 1.198,0.333 1.031,0.333 1.031,0.333 0.781,1.031 true 0.052,0.042 0.313,0.26 0.26,0.219 10 false *a 2.563,1.813 2.906,2.01 0.344,0.198 10 false ILL+ 1.24,0.271 1.583,0.469 0.344,0.198 10 false ILL-
*a Component without harness connected
(No. 2 Combination Switch Assembly (w/o Module Switch (2nd Start)))


Apply battery voltage between the terminals of the No. 2 combination switch assembly (w/o Module Switch (2nd Start)), and check the illumination condition of the No. 2 combination switch assembly (w/o Module Switch (2nd Start)).

OK:
Measurement Condition Specified Condition
Battery positive (+) → 13 (ILL+)
Battery negative (-) → 12 (ILL-)
Illuminates


If the result is not as specified, replace the No. 2 combination switch assembly (w/o Module Switch (2nd Start)).


Hide 84711 4.INSPECT ECO MODE SWITCH (Drive Mode)

a.
C380111C05
2.219,1.469 2.396,1.938 2.396,1.938 2.552,1.938 true 1.563,1.938 1.74,1.938 1.74,1.938 1.969,1.479 true 1.75,1 2.146,0.177 2.146,0.177 2.313,0.177 true 0.688,1.094 1.135,1.094 true 2.354,0.094 2.906,0.313 0.552,0.219 10 false SPORT 0.333,1.01 0.708,1.25 0.375,0.24 10 false GND 0.938,1.865 1.583,2.083 0.646,0.219 10 false NORMAL 2.583,1.854 3.396,2.063 0.813,0.208 10 false COMF ECO 0.042,0.042 0.302,0.302 0.26,0.26 10 false *a
*a Component without harness connected
(Eco Mode Switch (Drive Mode))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (SPORT) - 5 (GND) SPORT mode switch pushed and held Below 10 Ω
SPORT mode switch not pushed 10 kΩ or higher
7 (NORMAL) - 5 (GND) NORMAL mode switch pushed and held Below 10 Ω
NORMAL mode switch not pushed 10 kΩ or higher
6 (COMF ECO) - 5 (GND) COMF ECO mode switch pushed and held Below 10 Ω
COMF ECO mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the eco mode switch (Drive Mode).


b.
C380111C02
1.219,1.885 1.219,1.479 true 2.281,1.083 2.802,1.083 true 0.042,0.031 0.292,0.271 0.25,0.24 10 false *a 2.854,1.021 3.198,1.219 0.344,0.198 10 false ILL+ 1.135,1.906 1.479,2.104 0.344,0.198 10 false ILL-
*a Component without harness connected
(Eco Mode Switch (Drive Mode))


Apply battery voltage between the terminals of the eco mode switch (Drive Mode), and check the illumination condition of the eco mode switch (Drive Mode).

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (ILL+)
Battery negative (-) → 10 (ILL-)
Illuminates


If the result is not as specified, replace the eco mode switch (Drive Mode).