Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › from 2017.08
RM27T0E _59 Vehicle Exterior _053745 MIRROR (EXT) _0261253 OUTER REAR VIEW MIRROR A

MIRROR (EXT)  OUTER REAR VIEW MIRROR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the and LH sides.

·

The procedure listed below is for the LH side.

·

w/ Multi-terrain Monitor System:

When removing only the side television camera assembly, refer to TELEVISION CAMERA (for Side).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL



PROCEDURE

Hide 87961 1.REMOVE OUTER MIRROR GLASS

Hide 87945 2.REMOVE OUTER MIRROR COVER LH

B241698N05
1.344,1.333 1.542,1.542 0.198,0.208 10 true (1) 1.854,1.333 2.063,1.542 0.208,0.208 10 true (2) 2.271,1.156 2.458,1.365 0.188,0.208 10 true (3) 2.406,1.646 2.604,1.813 0.198,0.167 10 true (4) 2.125,2.042 2.333,2.219 0.208,0.177 10 true (5) 1.417,1.906 1.646,2.083 0.229,0.177 10 true (6) 0.781,1.552 1,1.771 0.219,0.219 10 true (7) 0.51,1.729 0.719,1.906 0.208,0.177 10 true (8)

HINT:

Be sure to detach the claws of the outer mirror cover LH in the order shown in the illustration.


a.
U115642C01
2.542,2.823 2.792,3.073 0.25,0.25 10 false *a
*a Protective Tape


Using 2 screwdrivers, detach the 2 claws.

HINT:

Tape the screwdriver tip before use.



b.

Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover LH.

NOTICE:

Be careful not to break the ribs.


HINT:

Tape the screwdriver tip before use.


B245757C03
5.865,1.802 5.865,2.021 false 6.344,1.302 6.417,0.979 6.417,0.979 6.531,0.979 false 5.573,0.771 5.823,0.802 false 6.552,0.927 6.781,1.115 0.229,0.188 10 true *a 5.802,2.052 6.021,2.24 0.219,0.188 10 false *b 5.396,0.667 5.604,0.833 0.208,0.167 10 true *c
*a Protective Tape *b Rib
*c Inner Side of Outer Mirror Cover - -



c.
B245758C02
2.021,0.865 2.552,0.74 2.552,0.74 2.208,1.094 false 2.615,0.635 2.896,0.917 0.281,0.281 10 false *a
*a Protective Tape


Put protective tape around the outer mirror cover LH and outer mirror body.


d.

Insert moulding remover A into the space made between the outer mirror body and outer mirror cover LH.

NOTICE:

Do not insert the moulding remover A more than 4 mm (0.157 in.).



e.
B245770C08
0.417,3.51 0.573,3.708 0.156,0.198 10 false *a
*a 40.0 mm (1.57 in.)


Slide the moulding remover A downwards as shown in the illustration to detach the 2 claws.

NOTICE:
·

Do not insert the moulding remover A more than 4 mm (0.157 in.).

·

Do not slide the moulding remover A past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover LH as the outer mirror body will become LH damaged.




f.

Remove the moulding remover A.


g.
U115640C02
0.552,1.156 0.771,1.354 0.219,0.198 10 false *a
*a Protective Tape


Put protective tape around the outer mirror cover LH and outer mirror body.


h.

Insert moulding remover A between the outer mirror cover LH and outer mirror body as shown in the illustration and detach the claw.


i.
B245633C06
1.969,0.792 2.125,1 2.125,1 2.25,1 false 2.271,0.906 2.458,1.104 0.188,0.198 10 false *a
*a Protective Tape


Using a screwdriver, detach the claw.

HINT:

Tape the screwdriver tip before use.



j.
B245761

Detach the 2 claws and remove the outer mirror cover LH.

NOTICE:

When removing the outer mirror cover LH, be careful not to damage the side turn signal light assembly LH.



Hide 81740 3.REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

Hide 87966 4.REMOVE OUTER MIRROR RETRACTOR LH (w/o Reverse Shift-linked Mirror)

a.

Remove the outer rear view mirror gasket LH.

i.
B279036C01
0.741,0.635 0.962,0.797 0.222,0.163 10 *a
*a Cut here


Cut the wire harness sub-assembly at the location shown in the illustration.

HINT:

A new wire harness sub-assembly is used for reassembly.



ii.
B279037C01
1.385,0.813 0.615,1.479 0.615,1.479 0.458,1.479 true 1.906,0.708 2.646,1.198 2.646,1.198 2.771,1.198 true 2.646,1.198 2.146,1.469 true 0.229,1.406 0.448,1.573 0.219,0.167 10 false *b 2.833,1.125 3.052,1.292 0.219,0.167 10 false *a
*a Tape
*b Clamp


Remove the tape and detach the clamp.



b.
U169792

Remove the screw.


c.

Detach the 5 claws and remove the outer rear view mirror gasket LH.


d.

Remove the lower mirror cover.

i.
B245769C03
1.292,0.323 1.427,0.177 1.427,0.177 1.583,0.177 false 1.615,0.094 1.854,0.323 0.24,0.229 10 false *a
*a Protective Tape


B278450N01
2.104,0.792 2.292,0.99 0.188,0.198 10 true (1) 2.229,1.094 2.417,1.26 0.188,0.167 10 true (2) 1.792,0.802 1.979,0.958 0.188,0.156 10 true (3) 1.656,1.26 1.844,1.448 0.188,0.188 10 true (4) 0.896,0.688 1.115,0.865 0.219,0.177 10 true (6) 1.323,0.719 1.521,0.896 0.198,0.177 10 true (5)

Put protective tape around the lower mirror cover.

HINT:

The claws of the mirror will be detached in the order shown in the illustration in the following steps.



ii.
U115638C01
1.625,1.135 1.031,1.406 1.031,1.406 0.677,1.406 true 0.479,1.323 0.656,1.51 0.177,0.188 10 false *a
*a Protective Tape


Using a screwdriver, detach the claw.

HINT:

Tape the screwdriver tip before use.



iii.
U115639C01
2.229,0.938 2.698,1.542 2.698,1.542 2.875,1.542 true 2.875,1.448 3.229,1.708 0.354,0.26 10 false *a
*a Protective Tape


Using a screwdriver, detach the claw.


iv.
U115641C01
2,1.594 2.656,1.25 2.656,1.25 2.865,1.25 true 2.969,1.188 3.344,1.531 0.375,0.344 10 false *a
*a Protective Tape


Using a screwdriver, detach the claw to create a space between the lower mirror cover and outer mirror body as shown in the illustration.


v.
B245768C03
1.885,1.063 2.188,1.406 2.188,1.406 2.271,1.406 true 2.281,1.323 2.469,1.479 0.188,0.156 10 false *a
*a Protective Tape


Insert a screwdriver as shown in the illustration.


vi.
B245766C03
2.219,0.844 2.594,0.979 2.594,0.979 2.594,1.135 true 2.49,1.177 2.74,1.458 0.25,0.281 10 false *a
*a Protective Tape


Detach the claw to create a space between the lower mirror cover and cover base as shown in the illustration.


vii.
B494128

While moving the lower mirror cover back and forth in the directions of the arrows in the illustration, detach the 2 claws and remove the lower mirror cover.



e.
B236356

Using a T25 "TORX" socket wrench, remove the 3 "TORX" screws.


f.

Remove the cover base.


g.
B241697

Remove the 5 screws and outer mirror body.


h.
B487988C01
0.99,2.135 1.229,2.406 0.24,0.271 10 false *a
*a Guide


Detach the guide and remove the cover body.

NOTICE:

Be careful as the guide shown in the part of the illustration is easily damaged.



i.

Remove the outer mirror actuator assembly LH.

i.
B494130C01
0,0 0,0 false
*a Cover


Slide the cover as shown in the illustration and disconnect the connector.


ii.
B375226

Pull out the wire harness sub-assembly in the direction indicated by the arrow in the illustration.


iii.
B279041

Remove the 3 screws and outer mirror actuator assembly LH.


iv.
B278346

Detach the 2 clamps and open the cover.


v.
B278347

Disconnect the connector and remove the outer mirror actuator assembly LH.



j.

Remove the support spring.

i.
B279044

Remove the 2 screws, and then detach the 6 claws and remove the 2 support springs.



Hide 86790C 5.REMOVE SIDE TELEVISION CAMERA ASSEMBLY (w/ Multi-terrain Monitor)