Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › from 2017.08
RM27T0E _59 Vehicle Exterior _053745 MIRROR (EXT) _0261253 OUTER REAR VIEW MIRROR A

MIRROR (EXT)  OUTER REAR VIEW MIRROR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

w/ Multi-terrain Monitor System:

When installing only the side television camera assembly, refer to TELEVISION CAMERA (for Side)

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>INSTALLATION



PROCEDURE

Hide 86790C 1.INSTALL SIDE TELEVISION CAMERA ASSEMBLY (w/ Multi-terrain Monitor)

Hide 87966 2.INSTALL OUTER MIRROR RETRACTOR LH (w/o Reverse Shift-linked Mirror)

a.

Attach the 6 claws to install the 2 support springs, and then install the 2 screws.


b.

Install the outer mirror actuator assembly LH.

i.
B278347

Connect the connector of a new wire harness sub-assembly.


ii.
B278346

Install the cover and attach the 2 clamps.


iii.
B293031

Install the outer mirror actuator assembly LH with the 3 screws.

NOTICE:

Install the outer mirror actuator assembly LH so that the wire harness sub-assembly is as shown in the illustration.




c.

Install the wire harness sub-assembly.

i.
B375226

Pass a new wire harness sub-assembly through the hole in the top of a new support sub-assembly in the direction indicated by the arrow in the illustration.


ii.
B494131C01
0,0 0,0 false
*a Cover


Connect the connector and slide the cover as shown in the illustration.



d.

Install the cover body.

i.

Pass the wire harness sub-assembly through the hole in the cover body.


ii.
B494125C01
1.021,1.458 1.25,1.656 0.229,0.198 10 false *a
*a Guide


Attach the guide as shown in the illustration to attach the cover body to the support sub-assembly.


iii.

Attach the outer mirror body as shown in the illustration.

B278476


iv.

Install the outer mirror body with the 5 screws.



e.

Install the cover base.

i.

Pass the wire harness sub-assembly through the hole in the cover base.


ii.

Using a T25 "TORX" socket wrench, install the cover base with 3 new "TORX" screws.

NOTICE:

Make sure that the wire harness sub-assembly is not pinched between parts.


Torque:
3.8 N*m (39 kgf*cm, 34 in.*lbf)



f.
B245821

Attach the 6 claws to install a new lower mirror cover.


g.

Install the outer rear view mirror gasket LH.

i.

Pass the wire harness sub-assembly through a new outer rear view mirror gasket LH.


ii.
U169792

Attach the 5 claws to install the outer rear view mirror gasket LH.


iii.

Install the screw.


iv.
B494124C03
1.531,0.125 1.844,0.323 0.313,0.198 10 false *a 2.708,1.198 3.021,1.396 0.313,0.198 10 false *b
*a 50 mm (1.97 in.)
*b 60 mm (2.36 in.)


Prepare the 3 sizes of new vinyl tapes as in indicated the illustration.


v.
B278471C04
1.771,1 2.094,0.646 2.094,0.646 2.198,0.646 false 1.719,1.177 2.073,1.542 2.073,1.542 2.208,1.542 true 2.26,1.49 2.563,1.719 0.302,0.229 10 false *b 2.24,0.583 2.542,0.813 0.302,0.229 10 false *a
*a Tape
*b Mark


Align the marking of the wire harness sub-assembly with the end of the wire harness sub-assembly insertion hole on the outer rear view mirror gasket LH and secure it with vinyl tape as shown in the illustration.

NOTICE:

Apply the vinyl tape securely so there is no gap between the vinyl tape and cable.



vi.
B276050C02
2.031,0.531 2.26,0.729 0.229,0.198 10 false *a 2.188,1.656 2.5,1.854 0.313,0.198 10 false *b
*a 30 mm (1.18 in.)
*b 50 mm (1.97 in.)


Apply vinyl tape in layers.

NOTICE:

Apply the tape securely so there is no gap between the vinyl tape and cable.



vii.
B276049C02
2.552,1.354 2.688,1.563 2.688,1.563 2.844,1.563 false 1.656,0.938 1.917,0.531 1.917,0.531 2.042,0.531 false 2.885,1.51 3.063,1.677 0.177,0.167 10 false *a 2.083,0.479 2.26,0.635 0.177,0.156 10 false *b 1.896,1.823 2.208,2.021 0.313,0.198 10 false *c
*a Clamp
*b Tape
*c 50 mm (1.97 in.)


Secure a new clamp using vinyl tape as shown in the illustration.



h.

Assemble the connector.

i.

Wrap the longer wire harness sub-assembly around the shorter one as shown in the part of the illustration labeled (1) until they are the same length.


ii.

Attach the 4 claws to connect the 2 connectors to a new adapter.

B494129C01
4.885,1.135 5.333,1 false 4.875,1.146 5.198,0.885 false 4.896,1.146 5.417,1.083 false 5.771,1.208 5.948,1.323 5.948,1.323 6.156,1.313 false 5.042,2.083 5.229,2.094 5.229,2.094 5.313,2.25 false 3.521,1.5 3.708,1.51 3.708,1.51 3.792,1.667 false 3.063,1.885 3.25,1.896 3.25,1.896 3.333,2.052 false 4.698,1.104 4.927,1.271 0.229,0.167 10 false *c 4.875,1.99 5.125,2.177 0.25,0.188 10 false (1) 6.219,1.24 6.448,1.406 0.229,0.167 10 false *c 3.365,1.417 3.594,1.583 0.229,0.167 10 false *b 2.885,1.792 3.115,1.958 0.229,0.167 10 false *a
*a Connector *b Adapter
*c Claw - -




Hide 81740 3.INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY LH

Hide 87945 4.INSTALL OUTER MIRROR COVER LH

a.

Install the outer mirror cover LH.

i.
B241700C01
2.75,1.979 2.927,1.479 2.927,1.479 3.052,1.479 false 3.094,1.396 3.313,1.594 0.219,0.198 10 false *a
*a Rib


Insert the rib on the outer edge of the outer mirror cover LH into the groove of the mirror body.

NOTICE:

Do not scratch the side turn signal light assembly LH.



ii.
U148020C01
3.031,1.521 2.135,0.823 true 1.104,0.958 1.958,0.823 1.958,0.823 1.021,1.542 true 1.958,0.708 2.146,0.896 0.188,0.188 10 false *a 3,0.948 3.188,1.125 0.188,0.177 10 false A 0.625,0.406 0.813,0.583 0.188,0.177 10 false B
*a Rib


Confirm that the outer mirror cover LH and mirror body are aligned properly, and then push the outer end of the cover to attach the outer claws.

NOTICE:
·

Make sure that the upper ribs of the outer mirror cover LH shown in part A of the illustration are properly attached to the mirror body.

·

Make sure that the ribs of the mirror body shown in part B of the illustration are not protruding from the outer mirror cover LH.




iii.
B241702

While making sure that the rib of the outer mirror cover LH fits properly into the groove of the mirror body, squeeze the inner end of the outer mirror cover LH and the mirror body together to attach the inner claws.


iv.
B241703

Push on the outer mirror cover LH at the locations of the 8 claws to confirm that the claws are attached properly.