Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TELEVISION CAMERA (for Side) › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261000 TELEVISION CAMERA(for Side) A

PARK ASSIST / MONITORING  TELEVISION CAMERA(for Side)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 86790C 1.INSTALL SIDE TELEVISION CAMERA ASSEMBLY

a.

Install the side television camera assembly with the 2 screws.


b.

Attach the clamp.


c.

Connect the connector.


d.
B278451C01
1.021,1.51 1.333,1.708 0.313,0.198 10 false *a
*a Guide


Attach the guide as shown in the illustration to attach the cover body to the support sub-assembly.

NOTICE:

Be careful not to break the guide.



e.

Attach the outer mirror body as shown in the illustration.

B278476


f.

Install the outer mirror body with the 5 screws.


g.

Using a T25 "TORX" socket wrench, install the cover base with 3 new "TORX" screws.

Torque:
3.8 N*m (39 kgf*cm, 34 in.*lbf)

NOTICE:

Make sure that the wire harness sub-assembly is not pinched between parts.



h.

Attach the 6 claws to install the lower mirror cover.


i.
U169792

Attach the 5 claws to connect the outer rear view mirror gasket LH.


j.

Install the screw.


k.
B278471C04
1.771,1 2.094,0.646 2.094,0.646 2.198,0.646 false 1.719,1.177 2.073,1.542 2.073,1.542 2.208,1.542 true 2.26,1.49 2.563,1.719 0.302,0.229 10 false *b 2.24,0.583 2.542,0.813 0.302,0.229 10 false *a
*a Tape
*b Mark


Align the marking of the wire harness sub-assembly with the end of the wire harness sub-assembly insertion hole on the outer rear view mirror gasket RH and secure it with vinyl tape as shown in the illustration.

NOTICE:

Apply the vinyl tape securely so there is no gap between the vinyl tape and cable.



l.
B276050C02
2.031,0.531 2.26,0.729 0.229,0.198 10 false *a 2.188,1.656 2.5,1.854 0.313,0.198 10 false *b
*a 30 mm (1.18 in.)
*b 50 mm (1.97 in.)


Apply new vinyl tape in layers.

NOTICE:

Apply the tape securely so there is no gap between the vinyl tape and cable.



m.
B276049C02
2.552,1.354 2.688,1.563 2.688,1.563 2.844,1.563 false 1.656,0.938 1.917,0.531 1.917,0.531 2.042,0.531 false 2.885,1.51 3.063,1.677 0.177,0.167 10 false *a 2.083,0.479 2.26,0.635 0.177,0.156 10 false *b 1.896,1.823 2.208,2.021 0.313,0.198 10 false *c
*a Clamp
*b Tape
*c 50 mm (1.97 in.)


Secure the clamp using vinyl tape as shown in the illustration.


Hide 81740 2.INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY LH

Hide 87945 3.INSTALL OUTER MIRROR COVER LH

Hide 87961 4.INSTALL OUTER REAR VIEW MIRROR GLASS

Hide 87940 5.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH