Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › from 2017.08
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261258 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85110 1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)

a.
E197600C02
2.99,2.323 3.104,2.323 3.104,2.323 3.271,2.198 false 0.5,1.125 0.354,1.125 false 3.198,0.677 3.375,0.875 0.177,0.198 10 false A 2.854,1.729 3.01,1.917 0.156,0.188 10 false B 0.333,2.729 0.479,2.917 0.146,0.188 10 false C 0.521,1.021 0.698,1.198 0.177,0.177 10 false *1 2.823,2.24 3,2.417 0.177,0.177 10 false *1
*1 Moulding Edge


Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

Standard:
Area Standard Condition
A 50.6 mm (1.992 in.)
B 31 mm (1.220 in.)
C 10.1 mm (0.398 in.)



b.
E201882C02
1.531,4.448 1.531,4.25 false 0.646,1.969 0.646,1.802 0.646,1.802 0.292,1.708 true 0.042,0.021 0.313,0.271 0.271,0.25 12 false *A 0.042,2.438 0.313,2.688 0.271,0.25 12 false *B 0.115,1.823 0.323,2.01 0.208,0.188 10 false a 1.01,4.417 1.208,4.594 0.198,0.177 10 false b 0.583,2.01 0.844,2.208 0.26,0.198 10 false *1 1.458,4.479 1.719,4.646 0.26,0.167 10 false *2
*A for RH Side
*B for LH Side
*1 Cowl Side Seal Edge
*2 Louver Edge


Stop the front wiper motor and link assembly operation.


c.

Check the automatic stop position.

OK:

The front wipers stop at the positions shown in the illustration.


Standard:
Area Standard Condition
a 27.3 to 47.3 mm (1.075 to 1.862 in.)
b 18.1 to 38.1 mm (0.713 to 1.500 in.)


If the result is not as specified, remove and reinstall the wiper arm and blade assembly, and then perform the on-vehicle inspection described above to inspect the wiper motor and link assembly again. If the result is not as specified again, inspect the wiper motor and link assembly with it removed from the vehicle body (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSPECTION).


Hide 85110 2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

a.
E197601C02
0.229,2.865 0.229,2.344 0.229,2.344 0.146,2.292 true 2.833,1.052 3.052,1.052 true 0.146,0.656 0.354,0.865 0.208,0.208 10 false A 0.51,1.729 0.719,1.906 0.208,0.177 10 false B 2.667,2.552 2.865,2.844 0.198,0.292 10 true C 0.167,2.927 0.438,3.177 0.271,0.25 10 false *1 2.667,0.979 2.875,1.198 0.208,0.219 10 false *1
*1 Moulding Edge


Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

Standard:
Area Standard Condition
A 50.6 mm (1.992 in.)
B 31 mm (1.220 in.)
C 14.1 mm (0.555 in.)



b.
E201883C02
2.823,2.083 2.823,1.823 2.823,1.823 3.188,1.688 true 1.906,4.25 1.906,4.479 true 2.75,2.135 3.063,2.417 0.313,0.281 10 false *1 1.813,4.479 1.99,4.625 0.177,0.146 10 false *2 0.042,0.021 0.354,0.302 0.313,0.281 12 false *A 0.052,2.313 0.365,2.594 0.313,0.281 12 false *B 3.198,1.896 3.354,2.177 0.156,0.281 10 false a 2.281,4.396 2.417,4.573 0.135,0.177 10 false b
*A for LH Side
*B for RH Side
*1 Cowl Side Seal Edge
*2 Louver Edge


Stop the front wiper motor and link assembly operation.


c.

Check the automatic stop position.

OK:

The front wipers stop at the positions shown in the illustration.


Standard:
Area Standard Condition
a 27.3 to 47.3 mm (1.075 to 1.862 in.)
b 18.1 to 38.1 mm (0.713 to 1.500 in.)


If the result is not as specified, remove and reinstall the wiper arm and blade assembly, and then perform the on-vehicle inspection described above to inspect the wiper motor and link assembly again. If the result is not as specified again, inspect the wiper motor and link assembly with it removed from the vehicle body (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSPECTION).