Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › 2017.08–2020.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260838 TRANSFER SYSTEM D

VF4BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

When a DTC is stored, the 4 wheel drive control ECU stores the current vehicle state as Freeze Frame Data.

HINT:

Freeze Frame Data at the time a DTC is stored:

When the 4 wheel drive control ECU stores data at the time a DTC is stored, no updates will be performed until the data is cleared.




CHECK FREEZE FRAME DATA


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Trouble Codes.


f.

According to the display on the GTS, select the trouble code data display with Freeze Frame Data.

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading/
Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
FL Wheel Speed Front wheel speed sensor LH reading/
Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
RR Wheel Speed Rear wheel speed sensor RH reading/
Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear wheel speed sensor LH reading/
Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
Vehicle Speed Maximum wheel speed sensor reading/
Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
Transfer Position Control SW for 1GR-FE, 1KD-FTV, 1GD-FTV:
Transfer position switch status/
ON or OFF
for 2TR-FE, 5L-E:
Transfer position switch status (transfer position switch input signal of LO terminal on ECU side)/
ON or OFF
for 1GR-FE, 1KD-FTV, 1GD-FTV:
ON: L4
OFF: H4
for 2TR-FE, 5L-E:
ON: H4L or L4L
OFF: H4F, between H4F and H4L or between H4L and L4L
-
Center Differential Lock Control SW Center differential lock switch status/
ON or OFF
ON: Switch pressed and held
OFF: Switch not pressed
for 1GR-FE, 1KD-FTV, 1GD-FTV
Center Differential Lock Position SW Center differential lock detection switch status/
ON or OFF
ON: Switch on (lock)
OFF: Switch off (free)
-
2-4 Changeover SW (2-4) Transfer positionswitch status (transfer position switch input signa lof 2-4 terminal on ECU side)
ON or OFF
ON: H4F or H4L
OFF: Between H4F and H4L, between H4L and L4L or L4L
for 2TR-FE, 5L-E
IG SW Ignition switch status/
ON or OFF
ON: Ignition switch ON -
Center Differential Lock Limit SW (TL2) Center differential lock limit switch (TL2) status/
ON or OFF
ON: Switching between free and lock, or set to lock
OFF: Set to free
-
Center Differential Lock Limit SW (TL3) Center differential lock limit switch (TL3) status/
ON or OFF
ON: Set to free or switching between free and lock
OFF: Set to lock
-
H-L Limit SW (HL1) High-low transfer limit switch (HL1) status/
ON or OFF
for 1GR-FE, 1KD-FTV, 1GD-FTV:
ON: L4 or switching between H4 and L4
OFF: H4
for 2TR-FE, 5L-E:
ON: Switching between H4L and L4L or L4L
OFF: H4F or H4L
-
H-L Limit SW (HL2) High-low transfer limit switch (HL2) status/
ON or OFF
for 1GR-FE, 1KD-FTV, 1GD-FTV:
ON: H4 or switching between H4 and L4
OFF: L4
for 2TR-FE, 5L-E:
ON: H4F, H4L or switching between H4L and L4L
OFF: L4L
-
Clutch SW Clutch start switch status/
ON or OFF
ON: Clutch pedal depressed
OFF: Clutch pedal released
Used only for vehicles with a manual transmission.
Displays OFF for vehicles with an automatic transmission.
Shift SW Status (N Range) Shift lever neutral condition/
ON or OFF
ON: Shift lever in N*1 or shift lever in neutral*2
OFF: Shift lever not in N*1 or shift lever not in neutral*2
-
Engine Fail Signal Engine control system malfunction status/
Normal or Abnormal
Normal: Engine control system normal Abnormal: Engine control system malfunctioning
Shift SW Status (P Range) Shift lever P condition/
ON or OFF
ON: Shift lever in P
OFF: Shift lever not in P
Used only for vehicles with an automatic transmission.
Displays OFF for vehicles with a manual transmission.
Stop Light SW Stop light switch assembly condition/
ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
VSC System VSC system availability/
Without or With
Without: w/o VSC
With: w/ VSC
-
VSC Fail Signal VSC system malfunction status/
Normal or Abnormal
Normal: VSC system normal Abnormal: VSC system malfunctioning or vehicle without VSC
Center Differential Lock Shift Motor Target Current Center differential lock shift motor driver circuit target current value/
Min.: 0.0 A
Max.: 25.5 A
Normal: 0.0 A
Switching: 0.0 to 25.5 A
-
H-L Shift Motor Target Current High-low transfer shift motor drive circuit target current value/
Min.: 0.0 A
Max.: 25.5 A
Normal: 0.0 A
Switching: 0.0 to 25.5 A
-
Motor Actual Current Motor drive circuit actual current value/
Min.: 0.0 A
Max.: 25.5 A
Normal: 0.0 A
Switching: 0.0 to 25.5 A
-
Motor Energization Status Signal Motor power signal status/
ON or OFF
ON: Power supplied to motor
OFF: Power not supplied to motor
-
C/C Cancel Request Cruise control cancellation signal status/
ON or OFF
ON: Cruise control cancellation requested
OFF: Cruise control cancellation not requested
-
L4 Position Signal L4 status signal/
ON or OFF
ON: L4 state
OFF: State other than L4
-
H-L Actuator Fail Signal High-low transfer actuator malfunction status/
Normal or Abnormal
Normal: High-low transfer actuator normal Abnormal: High-low transfer actuator malfunctioning
Center Differential Lock Position Signal Center differential lock condition signal/
ON or OFF
ON: Lock condition
OFF: Condition other than lock
-
Buzzer Request Buzzer sounding request/
Sound, Sound (3 times), No Sound
No Sound: Does not sound Sound (3 times): During a malfunction*3
L4 Indicator Request 4LO indicator light request/
Blink3, Blink2*4, Blink1, ON, OFF
·

Blink3: Indicator light rapidly blinks

·

Blink1: Indicator light blinks

·

ON: Indicator light illuminates

·

OFF: Indicator light turns off


·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)


Multi-Terrain Select Control Multi-terrain select control signal input/
OK or NG
OK: Multi-terrain select control is permitted
NG: Multi-terrain select control is prohibited
-
Center Differential Lock Indicator Request Center differential lock indicator light request/
Blink3, Blink2, Blink1, ON or OFF
·

Blink3: Indicator light rapidly blinks

·

Blink2: Indicator light blinks 3 times

·

Blink1: Indicator light blinks

·

ON: Indicator light illuminates

·

OFF: Indicator light turns off


·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)


IG Voltage IG monitor voltage/
Min.: 0.0 V
Max.: 25.5 V
11 to 14 V: Ignition switch ON -
Motor Voltage Motor driver circuit monitor voltage/
Min.: 0.0 V
Max.: 25.5 V
Normal: 1.5 to 12.0 V
Switching: 3.5 V
-
Mode Status Mode transition condition/
Initial Control, Particular Control at Start-Up, Shift Setting Control at Start-Up, H4F, H4L, L4F, L4L, L4LL*4, H4F->H4L, H4L->H4F, L4F->L4L, L4L->L4F, H4F->L4F, L4F->H4F, H4L->L4L, L4L->H4L, L4L->L4LL*4, L4LL->L4L*4, K7, K8, S04, S05, S06, S07, S08, S09, S10, S11, S14, S15, S16, S17, S18, B1, B2, B3, B4, B6, B7, B8, B9, HF1
Transition condition of the high-low transfer actuator, center differential lock actuator and differential lock shift actuator*6
HINT:
·

K7 or K8: Control while switching prohibited

·

S04 to S18: Control while switching limited

·

B1 to B9: During return control

·

HF1: During fuel control



Motor Relay (RY1-1) Internal ECU relay (RY1-1) condition*5/
ON or OFF
ON: Relay on
OFF: Relay off
-
Motor Relay (RY1-2) Internal ECU relay (RY1-2) condition*5/
ON or OFF
ON: Relay on
OFF: Relay off
-
Motor Relay (RY2-1) Internal ECU relay (RY2-1) condition*5/
ON or OFF
ON: Relay on
OFF: Relay off
-
Motor Relay (RY2-2) Internal ECU relay (RY2-2) condition*5/
ON or OFF
ON: Relay on
OFF: Relay off
-
AT/MT AT or MT identification/
AT or MT
AT: Automatic transmission
MT: Manual transmission
-
CAN Signal Invalid Status by IG Voltage Low Whether CAN communication data invalid condition due to IG voltage drop/
Valid or Inval
Valid: IG voltage 10 V or higher Inval: IG voltage below 10 V
SW Input Invalid Status by IG Voltage Low Input invalid condition of switches inside actuator due to IG voltage drop/
Valid or Inval
Valid: IG voltage 7.4 V or higher Inval: IG voltage below 7.4 V
Transfer Shift Invalid Status by IG Voltage Low Transfer shift actuator switching operation invalid condition due to IG voltage drop/
Valid or Inval
Valid: IG voltage 10 V or higher Inval: IG voltage below 10 V
Number of DTC Number of DTCs stored/
Min.: 0
Max.: 255
0 -

*1: for Automatic Transmission

*2: for Manual Transmission

*3: For details regarding malfunctions, refer to the buzzer sounding conditions of the diagnosis system (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>DIAGNOSIS SYSTEM).

*4: Item not equipped, therefore not displayed

*5: For the position of the relay, refer to the P17A9 wiring diagram (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>P17A9).

*6: w/ Rear Differential Lock




CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTCs will also clear the Freeze Frame Data.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Clear the DTCs and Freeze Frame Data (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>DTC CHECK / CLEAR).