Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2017.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260838 TRANSFER SYSTEM C

VF4BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17A9  Transfer Shift Motor Control Circuit Low  


DESCRIPTION

This DTC is output when a short to ground in the high-low transfer shift motor, center differential lock shift motor and differential lock shift motor* drive circuit is detected.

*: w/ Rear Differential Lock


DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17A9
1.

While the ignition switch is turned to ON or directly after the ignition switch is turned to ON (high-low transfer shift motor, center differential lock shift motor and differential lock shift motor* not operating)

2.

Short to ground in the high-low transfer shift motor, center differential lock shift motor and differential lock shift motor* drive circuit

3.

0.5 seconds or more (if directly after ignition switch is turned ON, 0.05 seconds or more)

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly

·

Differential lock shift actuator*



*: w/ Rear Differential Lock


WIRING DIAGRAM

C386010E02
0.698,1.583 1.802,2.063 1.104,0.479 10 false Center Differential Lock Shift Motor 0.354,2.552 2.365,2.792 2.01,0.24 10 false Center Differential Lock Actuator 0.625,3.76 1.698,4.208 1.073,0.448 10 false High-low Transfer Shift Motor 2.167,1.281 2.625,1.479 0.458,0.198 10 false TM1 2.521,1.302 2.677,1.5 0.156,0.198 10 false 2 4.177,2.083 4.333,2.281 0.156,0.198 10 false 8 4.396,2.073 4.854,2.271 0.458,0.198 10 false TM1 5.479,2.448 6.396,2.646 0.917,0.198 10 false RLY1-1 5.521,0.75 5.833,0.948 0.313,0.198 10 false IG 5.479,3.135 6.396,3.333 0.917,0.198 10 false RLY1-2 4.354,2.74 4.813,2.938 0.458,0.198 10 false TM2 4.177,2.729 4.333,2.927 0.156,0.198 10 false 7 2.156,1.938 2.615,2.135 0.458,0.198 10 false TM2 2.552,1.938 2.708,2.135 0.156,0.198 10 false 1 2.146,3.479 2.604,3.677 0.458,0.198 10 false HM1 2.531,3.49 2.688,3.688 0.156,0.198 10 false 8 2.156,4.167 2.615,4.365 0.458,0.198 10 false HM2 2.552,4.156 2.708,4.354 0.156,0.198 10 false 7 4.177,3.5 4.333,3.698 0.156,0.198 10 false 2 4.354,3.5 4.813,3.698 0.458,0.198 10 false HM1 4.354,4.156 4.813,4.354 0.458,0.198 10 false HM2 4.177,4.146 4.333,4.344 0.156,0.198 10 false 6 0.646,4.625 4.625,4.823 3.979,0.198 10 false High-low Transfer Actuator 0.625,6.094 1.656,6.51 1.031,0.417 10 false Differential Lock Shift Motor 0.771,5.125 5.667,5.323 4.896,0.198 10 false Transfer Shift Actuator Assembly 0.458,5.125 0.917,5.323 0.458,0.198 10 false C43 0.604,7.156 5.646,7.354 5.042,0.198 10 false Differential Lock Shift Actuator* 0.385,7.156 0.698,7.354 0.313,0.198 10 false E1 5.448,5.188 6.365,5.385 0.917,0.198 10 false RLY2-1 5.469,5.865 6.385,6.063 0.917,0.198 10 false RLY2-2 0.365,7.521 4.646,7.719 4.281,0.198 10 false *: w/ Rear Differential Lock 4.667,7.406 6.5,7.677 1.833,0.271 10 false 4 Wheel Drive Control ECU 4.24,7.375 4.698,7.573 0.458,0.198 10 false G54 6.188,5.865 6.5,6.063 0.313,0.198 10 false IG 4.385,4.833 4.698,5.031 0.313,0.198 10 false M1 4.135,4.844 4.292,5.042 0.156,0.198 10 false 3 3.229,4.896 3.385,5.094 0.156,0.198 10 false * 3.583,5.5 3.74,5.698 0.156,0.198 10 false * 2.26,5.823 2.573,6.021 0.313,0.198 10 false M1 2.563,5.802 2.719,6 0.156,0.198 10 false 3 2.25,6.5 2.563,6.698 0.313,0.198 10 false M2 2.51,6.5 2.667,6.698 0.156,0.198 10 false 2 4.177,5.531 4.333,5.729 0.156,0.198 10 false 9 4.375,5.521 4.688,5.719 0.313,0.198 10 false M2

PROCEDURE

1.CHECK ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR OR LOCK SHIFT MOTOR)
a.

Disconnect the G54 4 wheel drive control ECU connector.


b.
U164489E03
1.927,2.26 2.042,2.75 true 1.594,2.729 1.656,2.26 true 1.427,1.75 1.167,1.354 true 1.167,2.688 1.417,2.271 true 2.177,1.76 2.469,1.365 true 2.229,2.229 2.667,2.698 true 1.906,2.76 2.292,2.938 0.385,0.177 10 false TM1 1.667,0.938 1.99,1.115 0.323,0.177 10 false G54 0.188,0.135 0.573,0.313 0.385,0.177 10 false *a 1.396,2.75 1.781,2.927 0.385,0.177 10 false TM2 0.844,1.198 1.229,1.375 0.385,0.177 10 false HM1 0.885,2.719 1.271,2.896 0.385,0.177 10 false HM2 2.5,1.26 2.885,1.438 0.385,0.177 10 false M1*A 2.563,2.771 2.948,2.948 0.385,0.177 10 false M2*A

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Transfer Shift Actuator Assembly (High-low Transfer Shift Motor) Side
Tester Connection Condition Specified Condition
G54-2 (HM1) or G54-6 (HM2) - Body ground Always 10 kΩ or higher

Transfer Shift Actuator Assembly (Center Differential Lock Shift Motor) Side
Tester Connection Condition Specified Condition
G54-8 (TM1) or G54-7 (TM2) - Body ground Always 10 kΩ or higher

Differential Lock Shift Actuator (Differential Lock Shift Motor) Side (w/ Rear Differential Lock)
Tester Connection Condition Specified Condition
G54-3 (M1) or G54-9 (M2) - Body ground Always 10 kΩ or higher


Text in Illustration
*A w/ Rear Differential Lock
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)

Result:
Result Proceed to
OK A
NG (transfer shift actuator assembly (high-low transfer shift motor) side) B
NG (transfer shift actuator assembly (center differential lock shift motor) side) C
NG (differential lock shift actuator (differential lock shift motor) side (w/ Rear Differential Lock)) D




A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)

C

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)

D

4.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL LOCK SHIFT ACTUATOR - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the G54 4 wheel drive control ECU connector.


b.

Disconnect the C43 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-2 (HM1) or C43-8 (HM1) - Body ground Always 10 kΩ or higher
G54-6 (HM2) or C43-7 (HM2) - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the G54 4 wheel drive control ECU connector.


b.

Disconnect the C43 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-8 (TM1) or C43-2 (TM1) - Body ground Always 10 kΩ or higher
G54-7 (TM2) or C43-1 (TM2) - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL LOCK SHIFT ACTUATOR - BODY GROUND)
a.

Disconnect the G54 4 wheel drive control ECU connector.


b.

Disconnect the E1 differential lock shift actuator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-3 (M1) or E1-3 (M1) - Body ground Always 10 kΩ or higher
G54-9 (M2) or E1-2 (M2) - Body ground Always 10 kΩ or higher




OK

REPLACE DIFFERENTIAL LOCK SHIFT ACTUATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR