Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › 2017.08–2020.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260838 TRANSFER SYSTEM C

VF4BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17D0  Center Differential Lock Control SW Circuit  


DESCRIPTION

This DTC is output when a malfunction is detected in the center differential lock switch (combination switch assembly)*1*3, center differential lock switch (No. 2 combination switch assembly*2*3 or center differential lock switch*2*4.

*1: for 1GR-FE, 1KD-FTV, 1GD-FTV w/ Combination Switch

*2: for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch

*3: for Automatic Transmission

*4: for Manual Transmission


DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17D0
1.

While the ignition switch is turned to ON or directly after the ignition switch is turned to ON

2.

Center differential lock switch stuck ON

3.

0.3 seconds or more when ignition switch is turned to ON, or 60 seconds or more with ignition switch ON

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Center differential lock switch (combination switch assembly)*1*3

·

Center differential lock switch (No. 2 combination switch assembly)*2*3

·

Center differential lock switch*2*4



*1: for 1GR-FE, 1KD-FTV, 1GD-FTV w/ Combination Switch

*2: for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch

*3: for Automatic Transmission

*4: for Manual Transmission


WIRING DIAGRAM

C346659E03
1.125,3.25 4.219,3.615 3.094,0.365 10 false Center Differential Lock Switch (No. 2 Combination Switch Assembly)*2*3 1.167,1.115 3.365,1.323 2.198,0.208 10 false Center Differential Lock Switch*2*4 1.063,2.49 1.479,2.677 0.417,0.188 10 false G156 3.281,2.083 3.677,2.333 0.396,0.25 10 false 3 1.396,2.094 1.635,2.281 0.24,0.188 10 false 24 2.781,0.542 3.177,0.719 0.396,0.177 10 false CPU 1.146,0.948 1.573,1.135 0.427,0.188 10 false G230 4.719,2.948 5.01,3.135 0.292,0.188 10 false G53 4.74,3.125 6.563,3.344 1.823,0.219 10 false 4 Wheel Drive Control ECU 4.625,2.125 4.865,2.313 0.24,0.188 10 false 6 5.042,2.115 5.344,2.323 0.302,0.208 10 false DL 5.917,1.208 6.177,1.406 0.26,0.198 10 false IG 4.354,4.042 6.427,4.24 2.073,0.198 10 false *3: for Automatic Transmission 4.385,4.385 6.24,4.573 1.854,0.188 10 false *4: for Manual Transmission 1.458,0.521 1.625,0.74 0.167,0.219 10 false 2 3.167,0.531 3.563,0.781 0.396,0.25 10 false 5 2.781,2.125 3.177,2.302 0.396,0.177 10 false CPU 1.646,2.073 1.948,2.281 0.302,0.208 10 false E 1.667,0.5 1.969,0.708 0.302,0.208 10 false L 0.198,4.031 3.927,4.229 3.729,0.198 10 false *1: for 1GR-FE, 1KD-FTV, 1GD-FTV w/ Combination Switch 0.198,4.406 4.073,4.656 3.875,0.25 10 false *2: for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch 1.083,2.698 3.833,3.063 2.75,0.365 10 false Center Differential Lock Switch (Combination Switch Assembly)*1*3

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - COMBINATION SWITCH ASSEMBLY OR CENTER DIFFERENTIAL LOCK SWITCH)
a.

Disconnect the G53 4 wheel drive control ECU connector.


b.

for 1GR-FE, 1KD-FTV, 1GD-FTV w/ Combination Switch (Automatic Transmission):

Disconnect the G156 center differential lock switch (combination switch assembly) connector.

for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch (Automatic Transmission):

Disconnect the G156 center differential lock switch (No. 2 combination switch assembly) connector.


c.

for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch (Manual Transmission):

Disconnect the G230 center differential lock switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, 1KD-FTV, 1GD-FTV w/ Combination Switch (Automatic Transmission) or for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch (Automatic Transmission):
Tester Connection Condition Specified Condition
G53-6 (DL) - G156-3 (CPU) Always Below 1 Ω
G156-24 (E) - Body ground Always Below 1 Ω
G53-6 (DL) or G156-3 (CPU) - Body ground Always 10 kΩ or higher

for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch (Manual Transmission):
Tester Connection Condition Specified Condition
G53-6 (DL) - G230-5 (CPU) Always Below 1 Ω
G230-2 (L) - Body ground Always Below 1 Ω
G53-6 (DL) or G230-5 (CPU) - Body ground Always 10 kΩ or higher




OK

2.INSPECT COMBINATION SWITCH ASSEMBLY OR CENTER DIFFERENTIAL LOCK SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION SWITCH ASSEMBLY OR CENTER DIFFERENTIAL LOCK SWITCH
C281308E20
2.333,0.927 2.333,0.25 2.333,0.25 2.5,0.25 true 0.583,1.75 0.75,1.75 0.75,1.75 0.75,1.25 true 0.438,1.677 0.708,1.896 0.271,0.219 10 false E 2.563,0.167 2.938,0.396 0.375,0.229 10 false CPU 0.094,0.063 0.438,0.281 0.344,0.219 10 false *a*A 0.094,0.26 0.438,0.479 0.344,0.219 10 false *b*B

a.

for 1GR-FE, 1KD-FTV, 1GD-FTV w/ Combination Switch (Automatic Transmission):

Disconnect the G156 center differential lock switch (combination switch assembly) connector.

for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch (Automatic Transmission):

Disconnect the G156 center differential lock switch (No. 2 combination switch assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CPU) - 24 (E) Switch not pressed 10 kΩ or higher


Text in Illustration
*A for 1GR-FE, 1KD-FTV, 1GD-FTV w/ Combination Switch (Automatic Transmission)
*B for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch (Automatic Transmission)
*a Component without harness connected
(Center Differential Lock Switch (Combination Switch Assembly))
*b Component without harness connected
(Center Differential Lock Switch (No. 2 Combination Switch Assembly))


C381450E01
1.25,1.833 1.333,1.333 true 2.083,1.833 2.031,1.323 true 1.104,1.854 1.573,2.125 0.469,0.271 10 false CPU 2.094,1.854 2.438,2.073 0.344,0.219 10 false L 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a

c.

for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch (Manual Transmission):

Disconnect the G230 center differential lock switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (CPU) - 2 (L) Switch not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Center Differential Lock Switch)

Result:
Result Proceed to
OK A
NG for 1GR-FE, 1KD-FTV, 1GD-FTV w/ Combination Switch (Automatic Transmission) B
for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch (Automatic Transmission) C
for 1GR-FE, 1KD-FTV, 1GD-FTV w/o Combination Switch (Manual Transmission) D




A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B

C

D