Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (for 3 Door) › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053741 INTERIOR PANELS / TRIM _0261216 ROOF HEADLINING(for 3 Door) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for 3 Door)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 86101 1.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

Hide 82171 2.INSTALL NO. 1 ROOF WIRE

a.

Apply butyl tape to the roof headlining so that the tape is aligned with the wire harness marking as shown in the illustration.

HINT:

Use butyl tape that has a width of 10 mm (0.394 in.).


B240565C01
6.365,0.333 6.333,0.156 6.333,0.156 6.229,0.156 false 6.604,0.448 6.521,0.635 6.521,0.635 6.615,0.635 false 6.51,0.375 6.542,0.219 6.542,0.219 6.635,0.219 true 1.5,0.469 1.833,0.729 0.333,0.26 12 false *A 4.896,0.49 5.229,0.75 0.333,0.26 12 false *B 6.646,0.552 6.906,0.792 0.26,0.24 10 false *a 6.042,0.073 6.302,0.313 0.26,0.24 10 false *a 6.646,0.135 6.906,0.375 0.26,0.24 10 false *b
*A w/o Sliding Roof *B w/ Sliding Roof
*a Wire Harness Marking *b Butyl Tape



b.

Align the No. 1 roof wire with the wire harness installation points as shown in the illustration and attach it to the roof headlining assembly to install it.

HINT:

Be sure to securely attach the roof wire so that it is not twisted.



c.

Attach each clamp.

HINT:

Make sure the each wire harness are securely set into the cutouts of the roof headlining assembly.



d.

Turn the visor connectors approximately 90° clockwise to install them to the roof headlining assembly.

B486243C01
1.74,3.5 1.948,3.094 1.948,3.094 2.188,3.094 true 3.656,3.385 3.917,3.104 3.917,3.104 4.083,3.104 true 3.823,3.896 3.823,3.677 3.823,3.677 3.656,3.677 true 3.865,4.385 3.865,4.167 3.865,4.167 3.698,4.167 true 3.875,4.615 3.875,4.813 3.875,4.813 3.708,4.813 true 3.75,5 3.75,5.25 3.75,5.25 4,5.25 true 2.656,2.49 2.656,1.99 true 6.094,2.406 6.094,1.906 true 1.833,0.146 2.208,0.385 0.375,0.24 12 false *A 5.25,0.135 5.625,0.375 0.375,0.24 12 false *B 0.365,1.99 0.521,2.188 0.156,0.198 10 false A 0.99,0.26 1.146,0.458 0.156,0.198 10 false A 4.406,0.271 4.563,0.469 0.156,0.198 10 false A 3.635,1.531 3.792,1.729 0.156,0.198 10 false B 3.792,2 3.948,2.198 0.156,0.198 10 false A 0.198,1.49 0.354,1.688 0.156,0.198 10 false B 2.24,3.01 2.552,3.208 0.313,0.198 10 false *a 0.615,3.552 0.927,3.75 0.313,0.198 10 false A 3.49,2.833 3.802,3.031 0.313,0.198 10 false B 3.417,3.583 3.792,3.823 0.375,0.24 12 false *D 3.458,4.094 3.833,4.333 0.375,0.24 12 false *G 3.479,4.708 3.854,4.948 0.375,0.24 12 false *F 4.063,5.156 4.438,5.396 0.375,0.24 12 true *E 4.146,3.021 4.521,3.26 0.375,0.24 12 true *C 2.604,2.5 2.917,2.698 0.313,0.198 10 false *b 6.052,2.427 6.365,2.625 0.313,0.198 10 false *b
*A w/o Sliding Roof *B w/ Sliding Roof
*C w/ Rain Sensor, for LHD *D w/ EC Mirror
*E w/ Rain Sensor, for RHD *F w/ Pre-crash Safety System
*G w/ Pre-crash Safety System,w/ Camera Heater - -
*a Visor Connector *b Wire Harness Installation Point



Hide 81340J 3.INSTALL VANITY LIGHT ASSEMBLY LH

Hide 81340H 4.INSTALL VANITY LIGHT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 63344 5.INSTALL NO. 4 ROOF SILENCER PAD (w/o Sliding Roof)

B240556

a.

Align the No. 4 roof silencer pad with the markings on the roof headlining assembly and install the No. 4 roof silencer pad to the position shown in the illustration using hot-melt glue or double-sided tape.


Hide 63342 6.INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)

B240560

a.

Align the No. 2 roof silencer pad with the markings on the roof headlining assembly and install the No. 2 roof silencer pad to the position shown in the illustration using hot-melt glue or double-sided tape.


Hide 63341 7.INSTALL NO. 1 ROOF SILENCER PAD

B240557

a.

w/o Sliding Roof:

i.

Align the 3 No. 1 roof silencer pads with the markings on the roof headlining assembly and install the 3 No. 1 roof silencer pads to the position shown in the illustration using hot-melt glue or double-sided tape.



b.
B240562

w/ Sliding Roof:

i.

Align the No. 1 roof silencer pad with the markings on the roof headlining assembly and install the No. 1 roof silencer pad to the position shown in the illustration using hot-melt glue or double-sided tape.