Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1439  Steering Angle Sensor Initialization Incomplete  C1445  Vehicle Driven with Steering Angle Sensor not Initialized  


DESCRIPTION

The skid control ECU acquires steering sensor zero point every time the ignition switch is turned to ON and the vehicle is driven at 40 km/h (25 mph) or more for approximately 10 seconds. The ECU also stores the previous zero point.

The steering sensor zero point malfunction warning is canceled by turning the ignition switch off.

DTC Code DTC Detection Condition Trouble Area
C1439 After the steering sensor zero point calibration is cleared due to, for example, fluctuations in the power source, the steering sensor zero point calibration cannot be obtained for 60 seconds of continuous driving.
·

Steering sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Master cylinder solenoid)


C1445 Steering sensor zero point calibration cannot be obtained when the vehicle is driven without a record of steering sensor zero point calibration at a speed of 36 km/h (22 mph) or more for 30 seconds or more without the brake pedal being depressed.

CAUTION / NOTICE / HINT

NOTICE:
·

Before proceeding with the inspection, explain to the customer that the output DTC is related to temporary loss of the steering sensor zero point calibration, such as when the power voltage drops when the battery is removed, and confirm that this condition occurred.

·

When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).



HINT:
·

When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1439 and/or C1445, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>U0073).

·

When the speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) has trouble, DTCs for the steering sensor may be stored even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) are output together with other DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering sensor.



PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) and turn the steering wheel to the right and left, and then check that no speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output C1439 and/or C1445 A
Relating to CAN communication system (w/ Central Gateway ECU) B
Relating to CAN communication system (w/o Central Gateway ECU) C
Relating to speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) D
DTC is not output E

HINT:
·

If there is a malfunction in the speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output although the steering sensor is normal.

·

If the speed sensor and the yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output simultaneously, repair the sensors and inspect the steering sensor.

·

If DTC C1439 and/or C1445 is not output again, the DTC may have been stored due to a temporary loss of the steering sensor zero point calibration, such as when the power voltage drops.





A

2.PERFORM STEERING SENSOR ZERO POINT CALIBRATION

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

D

E

2.PERFORM STEERING SENSOR ZERO POINT CALIBRATION
a.

Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds.


b.

Check that the centered position of the steering wheel is correctly set while driving straight ahead.

HINT:

If the front wheel alignment and steering position are adjusted as a result of an abnormal centered position of the steering wheel, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.



OK:

The centered position of the steering wheel is correctly set.



OK

3.RECONFIRM DTC

NG

ADJUST FRONT WHEEL ALIGNMENT OR STEERING POSITION

3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and turn the steering wheel to the right and left.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTCs C1439 and C1445 are not output A
Yaw rate and acceleration sensor (airbag sensor assembly) and/or steering sensor DTC is output B

HINT:

If the same DTC C1439 and/or C1445 is not output again, the DTC may have been stored due to a temporary loss of the steering sensor zero point calibration, such as when the power voltage drops.




A

END

B