Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for Halogen Headlight) › from 2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0326211 LIGHTING SYSTEM(for Halogen Headlight) C

LIGHTING (EXT)  LIGHTING SYSTEM(for Halogen Headlight)  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects ambient light. The sensor creates an electrical signal based on the amount of light detected, and sends the signal to the main body ECU (multiplex network body ECU).

The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1244 Light Sensor Circuit Malfunction Either of the following conditions is met:
·

Malfunction in automatic light control sensor

·

Open or short in automatic light control sensor circuit


·

Harness or connector

·

Automatic light control sensor

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

E364105E08
5.208,3.635 6.875,4.021 1.667,0.385 10 false G217 5.208,2.729 6.406,3.031 1.198,0.302 10 false CLTE 5.208,2.104 6.406,2.406 1.198,0.302 10 false CLTS 5.208,0.958 6.406,1.26 1.198,0.302 10 false CLTB 4.896,2 6.094,2.302 1.198,0.302 10 false 20 4.896,0.958 6.094,1.26 1.198,0.302 10 false 19 4.906,2.729 6.104,3.031 1.198,0.302 10 false 21 2.021,2.719 3.219,3.021 1.198,0.302 10 false 2 2.021,1.99 3.219,2.292 1.198,0.302 10 false 4 2.031,0.927 3.229,1.229 1.198,0.302 10 false 1 1.51,2.708 2.708,3.01 1.198,0.302 10 false CLTE 1.5,1.969 2.698,2.271 1.198,0.302 10 false CLTS 1.49,0.958 2.688,1.26 1.198,0.302 10 false CLTB 0.229,3.625 1.427,3.927 1.198,0.302 10 false H84 0.229,3.771 2.875,3.958 2.646,0.188 10 false Automatic Light Control Sensor 5.208,3.802 6.875,4.188 1.667,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 6.26,0.646 6.75,0.865 0.49,0.219 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

w/ Entry and Start System:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS

b.

According to the display on the GTS, read the Data List and check that the value of Light Sensor Illuminance changes while performing the following:

i.

Turn the light control switch to the Auto position.


ii.

Cover the automatic light control sensor with an opaque object.


iii.

Slowly move the opaque object to uncover and then cover the automatic light control sensor.

Main Body
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Light Sensor Illuminance Light control sensor illuminance / 0 to 8191 lx Value is output according to ambient light level -

OK:

The value changes according to the amount the automatic light control sensor is covered.




Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - AUTOMATIC LIGHT CONTROL SENSOR)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the G217 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the H84 automatic light control sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G217-19 (CLTB) - H84-1 (CLTB) Always Below 1 Ω
G217-20 (CLTS) - H84-4 (CLTS) Always Below 1 Ω
G217-21 (CLTE) - H84-2 (CLTE) Always Below 1 Ω
G217-19 (CLTB) or H84-1 (CLTB) - Body ground Always 10 kΩ or higher
G217-20 (CLTS) or H84-4 (CLTS) - Body ground Always 10 kΩ or higher
G217-21 (CLTE) or H84-2 (CLTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
E203228C30
0.156,0.729 0.625,1.042 0.469,0.313 2.813,0.927 2.646,0.927 2.646,0.927 2.417,1.094 true 2.729,1.51 2.563,1.51 2.563,1.51 2.219,1.125 true 0.135,0.094 0.448,0.25 0.313,0.156 10 false *a 2.76,1.375 3.219,1.563 0.458,0.188 10 false CLTE 0.229,0.781 0.604,0.948 0.375,0.167 10 false G217 2.865,0.823 3.323,1.01 0.458,0.188 10 false CLTB
*a Component with harness connected
(Main Body ECU [Multiplex Network Body ECU])


Disconnect the H84 automatic light control sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G217-19 (CLTB) - G217-21 (CLTE) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK AUTOMATIC LIGHT CONTROL SENSOR

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CHECK AUTOMATIC LIGHT CONTROL SENSOR
a.

Using an oscilloscope, check the waveform.

E377391C01
1.729,0.229 2.25,0.469 0.521,0.24 2.604,1.521 2.969,1.844 2.969,1.844 3.167,1.844 true 2.49,1.51 2.729,2.146 2.729,2.146 2.927,2.146 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 3.875,0.323 4.188,0.479 0.313,0.156 10 false *b 6.281,1.75 6.813,2 0.531,0.25 10 false GND 3.25,1.708 3.781,1.958 0.531,0.25 10 false CLTS 2.979,2.01 3.51,2.26 0.531,0.25 10 false CLTE 1.813,0.271 2.24,0.458 0.427,0.188 10 false G217
*a Component with harness connected
(Main Body ECU [Multiplex Network Body ECU])
*b Waveform


OK:
Tester Connection Tool Setting Switch Condition Specified Condition
G217-20 (CLTS) - G217-21 (CLTE) 2 V/DIV., 10 ms./DIV. Automatic light control system operating Pulse generation
(Waveform)


HINT:

The communication waveform changes according to the surrounding brightness.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR