Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for Halogen Headlight) › from 2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0326211 LIGHTING SYSTEM(for Halogen Headlight) J

LIGHTING (EXT)  LIGHTING SYSTEM(for Halogen Headlight)  Headlight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives light control switch information signals and illuminates the low beam headlights.

WIRING DIAGRAM

E379781E01
6.156,1.01 6.771,1.208 0.615,0.198 10 false HRLY 5.844,1.042 6.458,1.24 0.615,0.198 10 false A 5.813,0.875 6.427,1.073 0.615,0.198 10 false 15 4.729,1.792 6.042,2.292 1.313,0.5 10 false Driver Side Junction Block Assembly 5.417,2.76 7.083,3.177 1.667,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 4.625,1.042 6.292,1.458 1.667,0.417 10 false 2M 5,1.031 6.667,1.448 1.667,0.417 10 false 2F 5,0.865 6.667,1.281 1.667,0.417 10 false 40 4.646,0.865 6.313,1.281 1.667,0.417 10 false 17 3.354,0.573 5.021,0.99 1.667,0.417 10 false 5 3.365,0.917 5.031,1.333 1.667,0.417 10 false 1 4.156,0.938 5.823,1.354 1.667,0.417 10 false 2 4.167,0.573 5.833,0.99 1.667,0.417 10 false 3 3.51,1.333 4.823,1.833 1.313,0.5 10 false H-LP LO 4.625,1.25 5.938,1.75 1.313,0.5 10 false *1 5.01,1.25 6.323,1.75 1.313,0.5 10 false *2 0.99,2.771 2.469,3.24 1.479,0.469 10 false A111 1,2.906 2.479,3.375 1.479,0.469 10 false Headlight Assembly LH 1,4.125 2.479,4.594 1.479,0.469 10 false A113 1,4.292 2.479,4.76 1.479,0.469 10 false Headlight Assembly RH 2.25,3.458 3.729,3.927 1.479,0.469 10 false B 2.26,2.094 3.74,2.563 1.479,0.469 10 false B 2.469,2.104 3.948,2.573 1.479,0.469 10 false 2 2.479,3.427 3.958,3.896 1.479,0.469 10 false 2 1.021,3.479 2.5,3.948 1.479,0.469 10 false LO 1.031,2.063 2.51,2.531 1.479,0.469 10 false LO 0.823,2.073 2.49,2.49 1.667,0.417 10 false 5 0.813,3.438 2.479,3.854 1.667,0.417 10 false 5 1.417,0.667 3.083,1.083 1.667,0.417 10 false from Battery 3.198,2.396 4.865,2.813 1.667,0.417 10 false H-LP LH-LO 3.167,3.74 4.833,4.156 1.667,0.417 10 false H-LP RH-LO 2.802,4.177 4.469,4.594 1.667,0.417 10 false *1: except 5L-E 2.823,4.469 4.51,4.708 1.688,0.24 10 false *2: for 5L-E

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the bulbs and fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

Before replacing the main body ECU (multiplex network body ECU), refer to Registration.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, perform the Active Test.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST

Main Body
Tester Display Test Part Control Range Diagnostic Note
Headlight Low beam headlights OFF or ON -

OK:

Low beam headlights turn on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HEADLIGHT RELAY (H-LP LO)
2.INSPECT HEADLIGHT RELAY (H-LP LO)
a.

Remove the headlight relay (H-LP LO) from the engine room relay block and junction block.


b.

Inspect the headlight relay (H-LP LO).

Click hereVehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - BATTERY)

NG

REPLACE HEADLIGHT RELAY (H-LP LO)

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - BATTERY)
a.
E371104C04
0.104,0.083 0.417,0.24 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Headlight Relay [H-LP LO])


Remove the headlight relay (H-LP LO) from the engine room relay block and junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Headlight relay (H-LP LO) terminal 1 - Body ground Always 11 to 14 V
Headlight relay (H-LP LO) terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND HEADLIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND HEADLIGHT ASSEMBLY)
a.

Remove the headlight relay (H-LP LO) from the engine room relay block and junction block.


b.

Disconnect the 2M*1 or 2F*2 driver side junction block assembly connector.

*1: except 5L-E

*2: for 5L-E



c.

Disconnect the A111 headlight assembly LH connector.


d.

Disconnect the A113 headlight assembly RH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except 5L-E
Tester Connection Condition Specified Condition
Headlight relay (H-LP LO) terminal 2 - 2M-17 Always Below 1 Ω
Headlight relay (H-LP LO) terminal 3 - A111-2 (B) Always Below 1 Ω
Headlight relay (H-LP LO) terminal 2 or 2M-17 - Body ground Always 10 kΩ or higher
Headlight relay (H-LP LO) terminal 3 or A111-2 (B) - Body ground Always 10 kΩ or higher

for 5L-E
Tester Connection Condition Specified Condition
Headlight relay (H-LP LO) terminal 2 - 2F-40 Always Below 1 Ω
Headlight relay (H-LP LO) terminal 3 - A111-2 (B) Always Below 1 Ω
Headlight relay (H-LP LO) terminal 2 or 2F-40 - Body ground Always 10 kΩ or higher
Headlight relay (H-LP LO) terminal 3 or A111-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

E379782C01
0.865,0.26 1.271,0.479 0.406,0.219 2.844,0.292 3.25,0.51 0.406,0.219 5.365,0.333 5.771,0.552 0.406,0.219 4.958,1.313 5.156,1.313 5.156,1.313 5.427,0.979 true 1.365,0.281 1.677,0.438 0.313,0.156 10 false *A 3.302,0.281 3.615,0.438 0.313,0.156 10 false *B 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 5.531,0.365 5.688,0.521 0.156,0.156 10 false A 2.969,0.302 3.219,0.5 0.25,0.198 10 false 2F 0.979,0.271 1.229,0.469 0.25,0.198 10 false 2M 4.563,1.188 5.073,1.469 0.51,0.281 10 false HRLY
*A except 5L-E *B for 5L-E
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except 5L-E
Tester Connection Condition Specified Condition
2M-17 - A-15 (HRLY) Always Below 1 Ω

for 5L-E
Tester Connection Condition Specified Condition
2F-40 - A-15 (HRLY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY