Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2017.08–2020.08
RM27T0E _59 Vehicle Exterior _053744 DOOR / HATCH _0261247 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 67492A 2.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.
B240614

Detach the 2 clips and remove the front door lower frame bracket garnish LH.


Hide 69298A 3.REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

a.
B238520

Using a moulding remover, detach the 3 claws and remove the inside handle bezel LH as shown in the illustration.


Hide 74611C 4.REMOVE ASSIST GRIP COVER LH

a.
B238521

Using moulding remover A, detach the 8 claws and remove the assist grip cover LH.


Hide 67602 5.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B238522

Remove the 3 screws.


b.

Remove the 12 clips.


c.
B238523C02
1.552,3.333 1.188,3.333 1.188,3.333 1.01,3.677 true 1.604,3.24 1.865,3.448 0.26,0.208 10 false *a
*a Reference Boss


Pull out the front door trim board sub-assembly LH in the direction indicated by the arrow in the illustration.


d.

Raise the front door trim board sub-assembly LH to detach the 4 claws and remove the front door trim board sub-assembly LH together with the front door inner glass weatherstrip LH.


e.
B238524

Disconnect the 2 connectors.


f.

w/ Seat Position Memory System:

i.
B240206

Disconnect the connector.



g.
B238525

Disconnect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.


Hide 68172A 6.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B238526

Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip LH from the front door trim board sub-assembly LH as shown in the illustration.


Hide 81910A 7.REMOVE FRONT REFLEX REFLECTOR ASSEMBLY

a.
E198063

Detach the 2 claws and remove the front reflex reflector assembly.


Hide 81080E 8.REMOVE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH (w/ Personal Light)

Hide 81080L 9.REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY LH (w/ Personal Light)

Hide 84927 10.REMOVE SEAT MEMORY SWITCH (w/ Seat Position Memory System)

Hide 84040 11.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)

a.
B238528

Remove the 3 screws and the multiplex network master switch assembly.


Hide 84810 12.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 69206B 13.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B238529

Remove the 8 screws and door assist grip assembly LH.


b.
B238527

Remove the 2 screws.


c.

Detach the guide and 2 claws and remove the front door inside handle sub-assembly LH from the front door trim board sub-assembly LH.


Hide 89430A 14.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Reverse Shift-linked Mirror)

Hide 86160 15.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 89860A 16.REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH

Hide 67832 17.REMOVE FRONT DOOR SERVICE HOLE COVER LH

a.
B238530

Remove the bolt.


b.

Detach the 2 clamps, move the wire harness out of the way and remove the front door service hole cover LH.

HINT:

Remove any remaining butyl tape from the front door panel.



Hide 87940 18.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 68102 19.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Connect the cable to the negative (-) battery terminal.


b.

Connect the multiplex network master switch assembly and move the front door glass sub-assembly LH so that the door glass bolts can be seen.


c.

Disconnect the cable from the negative (-) battery terminal and multiplex network master switch assembly.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




d.
B238531

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the front door glass sub-assembly LH to fall.



e.
B238532N02
0.365,0.427 0.635,0.656 0.271,0.229 10 true (1) 2.469,0.188 2.698,0.406 0.229,0.219 10 true (2)

Remove the front door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly LH.



Hide 69802 20.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B238533C02
2.094,1.302 1.885,1.302 true 1.677,1.229 1.979,1.469 0.302,0.24 10 true *1
*1 Temporary Bolt


Disconnect the connector.


b.

Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator sub-assembly LH may fall and cause damage.



c.

Remove the 5 bolts.


d.

Remove the front door window regulator sub-assembly LH.


e.

Remove the temporary bolt from the front door window regulator sub-assembly LH.


Hide 85720C 21.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 68151D 22.REMOVE FRONT DOOR GLASS RUN LH

a.
B238535

Remove the front door glass run LH.


Hide 67664C 23.REMOVE DOOR FRAME GARNISH LH

a.
B238558

Detach the clip and remove the door frame garnish LH.


Hide 67404F 24.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B238536

Remove the bolt and front door rear lower frame sub-assembly LH as shown in the illustration.


Hide 25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B238537

Remove the hole plug.


b.
B238538

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly LH.



Hide 69217D 26.REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)

a.
B238539

Using a screwdriver, detach the claw and remove the front door outside handle cover LH.


Hide 69217D 27.REMOVE FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)

a.
B241166

Remove the hole plug.


b.
B238540

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover RH.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly RH.



Hide 69220 28.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.

w/ Entry and Start System:

i.
B238541

Detach the 2 claws.


ii.

Disconnect the connector.



b.
B238542

Move the lever in the direction indicated by the arrow in the illustration.


c.
B238543

Remove the front door outside handle assembly LH as shown in the illustration.


Hide 69252 29.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

a.
B238544

Detach the 3 claws and remove the front door front outside handle pad LH.


Hide 69254C 30.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD LH

a.
B238545

Detach the 2 claws and remove the front door rear outside handle pad LH.


Hide 69040A 31.REMOVE FRONT DOOR LOCK ASSEMBLY LH

Hide 69720B 32.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B238548

Remove the front door lock remote control cable assembly LH.


Hide 69760C 33.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B238549

Using a screwdriver, detach the 3 claws.

HINT:

Tape the screwdriver tip before use.



b.
B238550

Remove the front door inside locking cable assembly LH.


Hide 69202A 34.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

w/ Entry and Start System:

i.
B238551

Disconnect the connector.


ii.

Detach the clamp and remove the front door wire LH.



b.
B238553

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Slide the front door outside handle frame sub-assembly LH to detach the door handle nut and claw of the front door outside handle frame sub-assembly LH, and then remove the front door outside handle frame sub-assembly LH.


Hide 82152A 35.REMOVE FRONT DOOR WIRE LH (w/ Entry and Start System)

a.
B238552

Detach the 4 clamps and remove the front door wire LH.


Hide 69312 36.REMOVE FRONT DOOR LOCK OPEN ROD LH

a.
B238554N02
2.917,2.5 3.167,2.75 0.25,0.25 10 true (2) 2.479,1.917 2.75,2.135 0.271,0.219 10 true (1)

Remove the front door lock open rod LH as indicated by the arrows, in the order shown in the illustration.


Hide 67924 37.REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION

a.
B238555C05
2.417,1.167 2.083,1.167 2.083,1.167 1.667,0.667 true 2.458,1.083 2.75,1.281 0.292,0.198 10 false *a
*a Double-sided Tape


Remove the 2 bolts.


b.

Detach the 2 claws and remove the front door No. 2 stiffener cushion.


Hide 68620 38.REMOVE FRONT DOOR CHECK ASSEMBLY LH

a.
B238556

Remove the bolt, 2 nuts and front door check assembly LH.


Hide 67862 39.REMOVE FRONT DOOR WEATHERSTRIP LH

a.
B238557

Using a clip remover, detach the 21 clips and remove the front door weatherstrip LH.


Hide 75712B 40.REMOVE FRONT DOOR BELT MOULDING LH

Hide 75756C 41.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

Hide 75922M 42.REMOVE NO. 1 BLACK OUT TAPE LH

Hide 75986F 43.REMOVE FRONT DOOR OUTSIDE STRIPE LH

Hide 75976G 44.REMOVE NO. 2 FRONT DOOR STRIPE LH

Hide 67001A 45.REMOVE FRONT DOOR PANEL CUSHION

a.
B240615

Using a clip remover, detach the clip and remove the door panel cushion.