Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1655  Seat Belt Buckle Switch (RH)  


DESCRIPTION

The seat belt buckle switch RH circuit consists of the center airbag sensor and front seat inner belt RH.

DTC B1655 is stored when a malfunction is detected in the seat belt buckle switch RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1655 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the seat belt buckle switch RH circuit for 2 seconds.

·

A front seat inner belt RH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat inner belt assembly RH (Seat belt buckle switch RH)

·

Center airbag sensor



WIRING DIAGRAM

C213926E23
5.719,4.094 7.115,4.281 1.396,0.188 10 false Center Airbag Sensor 0.406,4.146 2.417,4.354 2.01,0.208 10 false Front Seat Inner Belt RH 5.865,2.917 6.344,3.198 0.479,0.281 10 false RBE- 5.719,3.906 6.063,4.083 0.344,0.177 10 false Q43 0.406,3.948 0.865,4.198 0.458,0.25 10 false Q34 5.875,1.354 6.323,1.646 0.448,0.292 10 false RBE+ 1.99,3.094 2.396,3.396 0.406,0.302 10 false RBE- 2.01,1.229 2.552,1.531 0.542,0.302 10 false RBE+ 5.563,3.094 5.896,3.385 0.333,0.292 10 false 23 5.573,1.5 5.927,1.802 0.354,0.302 10 false 15 2.458,3.094 2.823,3.385 0.365,0.292 10 false 1 2.458,1.521 2.698,1.813 0.24,0.292 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front seat inner belt RH.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front seat inner belt RH.


b.
C208245C35
0.329,1.776 0.522,1.944 0.193,0.168 10 *1 2.136,1.776 2.329,1.944 0.193,0.168 10 *2
*1 Front Seat Inner Belt RH
*2 Center Airbag Sensor


Check that the connectors (on the center airbag sensor side and front seat inner belt RH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

4.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C385808C01
2.896,0.51 3.229,0.719 0.333,0.208 4.979,0.271 5.313,0.479 0.333,0.208 3.188,1.146 3.542,0.927 true 4.104,1.167 3.76,0.938 true 5.156,0.781 5.594,0.844 true 5.354,1.448 5.604,0.99 true 0.604,1.281 0.917,1.479 0.313,0.198 10 false *1 1.813,1.135 2.125,1.333 0.313,0.198 10 false *2 1.635,0.698 1.948,0.896 0.313,0.198 10 false A 1.375,1.115 1.688,1.313 0.313,0.198 10 false B 1.094,1.104 1.406,1.302 0.313,0.198 10 false C 0.802,0.917 1.115,1.115 0.313,0.198 10 false D 3.583,0.281 3.896,0.479 0.313,0.198 10 false *a 5.698,0.208 6.01,0.406 0.313,0.198 10 false *b 3.031,1.167 3.5,1.406 0.469,0.24 10 false RBE- 3.99,1.167 4.458,1.406 0.469,0.24 10 false RBE+ 4.781,0.698 5.25,0.938 0.469,0.24 10 false RBE+ 5.198,1.448 5.667,1.688 0.469,0.24 10 false RBE- 2.938,0.531 3.396,0.729 0.458,0.198 10 false Q34 5.021,0.302 5.479,0.5 0.458,0.198 10 false Q43
*1 Front Seat Inner Belt RH *2 Center Airbag Sensor
*3 Connector C *4 Connector B
*a Front view of wire harness connector
(to Front Seat Inner Belt RH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q34-2 (RBE+) - Body ground Ignition switch ON Below 1 V
Q34-1 (RBE-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q34-2 (RBE+) - Q43-15 (RBE+) Always Below 1 Ω
Q34-1 (RBE-) - Q43-23 (RBE-) Always Below 1 Ω
Q34-2 (RBE+) - Body ground Always 1 MΩ or higher
Q34-1 (RBE-) - Body ground Always 1 MΩ or higher




OK

5.CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)
a.
C171812C48
0.719,1.271 0.875,1.438 0.156,0.167 10 *1 1.844,1.125 2.031,1.292 0.188,0.167 10 *2
*1 Front Seat Inner Belt RH
*2 Center Airbag Sensor


Connect the connectors to the center airbag sensor and front seat inner belt RH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.




OK

NG

6.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
6.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt RH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the inspection using parts from a normally functioning vehicle if possible.




NEXT

7.CHECK CENTER AIRBAG SENSOR
7.CHECK CENTER AIRBAG SENSOR
a.
C171812C49
0.719,1.271 0.875,1.438 0.156,0.167 10 *1 1.844,1.125 2.031,1.292 0.188,0.167 10 *2
*1 Front Seat Inner Belt RH
*2 Center Airbag Sensor


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.




OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG