The circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH and curtain shield airbag LH or RH) is composed of the center airbag sensor, rear airbag sensor LH or RH and side airbag sensor LH or RH.
The rear airbag sensor LH or RH and side airbag sensor LH or RH detect impacts to the vehicle and send signals to the center airbag sensor to determine if the airbag should be deployed.
DTC B1692 or B1697 is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH and curtain shield airbag LH or RH).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1692 | One of the following conditions is met:
·
The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH (to determine deployment of the front seat side airbag RH and curtain shield airbag RH) for 2 seconds. ·
A side airbag sensor RH malfunction. ·
A rear airbag sensor RH malfunction. ·
A center airbag sensor malfunction. |
·
Floor wire ·
Front door wire RH ·
Side airbag sensor RH ·
Rear airbag sensor RH ·
Center airbag sensor |
| B1697 | One of the following conditions is met:
·
The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH (to determine deployment of the front seat side airbag LH and curtain shield airbag LH) for 2 seconds. ·
A side airbag sensor LH malfunction. ·
A rear airbag sensor LH malfunction. ·
A center airbag sensor malfunction. |
·
No. 2 floor wire ·
Front door wire LH ·
Side airbag sensor LH ·
Rear airbag sensor LH ·
Center airbag sensor |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
After replacing the center airbag sensor, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Turn the ignition switch to ON.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1692 and B1697 are not output | A |
| DTC B1697 is output | B |
| DTC B1692 is output | C |
Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.
C
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor RH and side airbag sensor RH.
The connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor, rear airbag sensor RH and side airbag sensor RH.
Check that the connectors (on the center airbag sensor side, rear airbag sensor RH side and side airbag sensor RH side) are not damaged.
The connectors are not deformed or damaged.
| *1 | Rear Airbag Sensor RH |
| *2 | Side Airbag Sensor RH |
| *3 | Center Airbag Sensor |
OK
NG
Connect the connectors to the center airbag sensor and side airbag sensor RH.
Interchange the rear airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1692 and B1697 are not output | A |
| DTC B1697 is output (for 3 Door) | B |
| DTC B1697 is output (for 5 Door) | C |
| DTC B1692 is output | D |
Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.
| *1 | Rear Airbag Sensor LH |
| *2 | Center Airbag Sensor |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.
D
A
B
C
Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.
| *1 | Side Airbag Sensor RH | *2 | Rear Airbag Sensor RH |
| *3 | Connector E | *4 | Connector B |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Side Airbag Sensor RH) |
*b | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Q4-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| Q4-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q4-1 (BCR+) - Q4-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q4-1 (BCR+) - Q4-2 (BCR-) | Always | 1 MΩ or higher |
| Q4-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| Q4-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Connect the connector to the rear airbag sensor RH.
Interchange the side airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1692 and B1697 are not output | A |
| DTC B1697 is output | B |
| DTC B1692 is output | C |
Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.
| *1 | Side Airbag Sensor LH |
| *2 | Rear Airbag Sensor RH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
C
A
B
Disconnect the floor wire connector from the front door wire RH.
| *1 | Side Airbag Sensor RH | *2 | Rear Airbag Sensor RH |
| *3 | Front Door Wire RH | *4 | Floor Wire |
| *5 | Connector C | *6 | Connector B |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
*b | Front view of wire harness connector
(to Rear Airbag Sensor RH) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Q4-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| Q4-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q4-1 (BCR+) - Q4-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q4-1 (BCR+) - Q4-2 (BCR-) | Always | 1 MΩ or higher |
| Q4-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| Q4-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor LH and side airbag sensor LH.
The connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor, rear airbag sensor LH and side airbag sensor LH.
| *1 | Rear Airbag Sensor LH |
| *2 | Side Airbag Sensor LH |
| *3 | Center Airbag Sensor |
Check that the connectors (on the center airbag sensor side, rear airbag sensor LH side and side airbag sensor LH side) are not damaged.
The connectors are not deformed or damaged.
OK
NG
| *1 | Rear Airbag Sensor RH |
| *2 | Center Airbag Sensor |
Connect the connector to the center airbag sensor and side airbag sensor LH.
Interchange the rear airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1692 and B1697 are not output | A |
| DTC B1692 is output (for 3 Door) | B |
| DTC B1692 is output (for 5 Door) | C |
| DTC B1697 is output | D |
Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.
D
A
B
C
Disconnect the connectors from the rear airbag sensor LH and side airbag sensor LH.
| *1 | Side Airbag Sensor LH | *2 | Rear Airbag Sensor LH |
| *3 | Connector E | *4 | Connector B |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Side Airbag Sensor LH) |
*b | Front view of wire harness connector
(to Rear Airbag Sensor LH) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| R4-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| R4-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R4-1 (BCL+) - R4-2 (BCL-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R4-1 (BCL+) - R4-2 (BCL-) | Always | 1 MΩ or higher |
| R4-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| R4-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
OK
NG
Connect the connector to the rear airbag sensor LH.
Interchange the side airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1692 and B1697 are not output | A |
| DTC B1692 is output | B |
| DTC B1697 is output | C |
Codes other than DTC B1692 and B1697 may be output at this time, but they are not related to this check.
| *1 | Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor LH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
C
A
B
Disconnect the No. 2 floor wire connector from the front door wire LH.
| *1 | Side Airbag Sensor LH | *2 | Rear Airbag Sensor LH |
| *3 | Front Door Wire LH | *4 | No. 2 Floor Wire |
| *5 | Connector C | *6 | Connector B |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Front Door Wire LH) |
*b | Front view of wire harness connector
(to Rear Airbag Sensor LH) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| R4-1 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| R4-2 (BCL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R4-1 (BCL+) - R4-2 (BCL-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R4-1 (BCL+) - R4-2 (BCL-) | Always | 1 MΩ or higher |
| R4-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| R4-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
OK
NG