Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1825  Short in Side Squib (LH) Circuit  B1826  Open in Side Squib (LH) Circuit  B1827  Short in Side Squib (LH) Circuit (to Ground)  B1828  Short in Side Squib (LH) Circuit (to +B)  


DESCRIPTION

The side squib LH circuit consists of the center airbag sensor and front seat airbag LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1825 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the side squib LH circuit during the primary check.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Center airbag sensor


B1826 One of the following conditions is met:
·

The center airbag sensor detects open circuit signal in the side squib LH circuit for 2 seconds.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Center airbag sensor


B1827 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the side squib LH circuit for 0.5 seconds.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Center airbag sensor


B1828 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the side squib LH circuit for 0.5 seconds.

·

A side squib LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly LH (Side squib LH)

·

Center airbag sensor



WIRING DIAGRAM

C385818E02
2.021,1.563 2.635,1.76 0.615,0.198 10 false SFL+ 2.01,2.635 2.625,2.833 0.615,0.198 10 false SFL- 0.865,3.021 1.188,3.281 0.323,0.26 10 false R6 0.865,3.219 2.198,3.573 1.333,0.354 10 false Side Squib LH 2.458,2.385 3.073,2.583 0.615,0.198 10 false 2 2.448,1.563 3.063,1.76 0.615,0.198 10 false 1 4.552,1.563 5.167,1.76 0.615,0.198 10 false 1 4.573,2.385 4.906,2.615 0.333,0.229 10 false 2 4.792,1.688 5.406,1.885 0.615,0.198 10 false SFL+ 4.802,2.51 5.417,2.708 0.615,0.198 10 false SFL- 4.792,4.146 5.115,4.406 0.323,0.26 10 false R49 4.792,4.323 7.021,4.521 2.229,0.198 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

After replacing the center airbag sensor, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT AIR BAG ASSEMBLY LH (SIDE SQUIB LH)
a.
E272064C05
0.198,2 0.615,2.229 0.417,0.229 2.01,2.823 2.219,3 false 1.021,0.052 1.333,0.208 0.313,0.156 10 false *1 2.219,1.188 2.531,1.344 0.313,0.156 10 false *2 2.365,1.969 2.677,2.125 0.313,0.156 10 false *3 2.26,2.979 2.573,3.135 0.313,0.156 10 false *4 1.5,1.458 1.813,1.615 0.313,0.156 10 false *a 0.313,2.021 0.74,2.24 0.427,0.219 10 false R6 2,0.229 2.313,0.385 0.313,0.156 10 false A 1.469,0.5 1.792,0.729 0.323,0.229 10 false C 1.25,0.5 1.573,0.729 0.323,0.229 10 false D
*1 Side Squib LH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Side Squib LH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat airbag LH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825, B1826, B1827 or B1828 is not output.


HINT:

Codes other than DTC B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB LH CIRCUIT)
2.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB LH CIRCUIT)
a.
C314152C08
0.438,2.313 0.719,2.531 0.281,0.219 1.083,0.188 0.948,0.188 0.948,0.188 0.948,0.51 false 1.635,0.198 1.5,0.198 1.5,0.198 1.5,0.521 false 2.104,2.958 1.656,2.792 true 0.813,3.021 1.365,2.802 true 1.094,0.083 1.406,0.24 0.313,0.156 10 false *1 1.656,0.094 1.969,0.25 0.313,0.156 10 false *2 1.906,1.427 2.219,1.583 0.313,0.156 10 false *3 2.333,2.354 2.646,2.51 0.313,0.156 10 false *4 1.406,1.927 1.719,2.083 0.313,0.156 10 false *a 2.094,0.469 2.25,0.667 0.156,0.198 10 false A 1.698,0.771 1.854,0.969 0.156,0.198 10 false B 1.281,0.76 1.438,0.958 0.156,0.198 10 false C 1.083,0.76 1.24,0.958 0.156,0.198 10 false D 0.479,2.333 0.792,2.531 0.313,0.198 10 false R6 0.563,3.021 1.083,3.219 0.521,0.198 10 false SFL+ 2.094,2.979 2.615,3.177 0.521,0.198 10 false SFL-
*1 Side Squib LH
*2 No. 2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Side Squib LH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R6-1 (SFL+) - Body ground Ignition switch ON Below 1 V
R6-2 (SFL-) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R6-1 (SFL+) - R6-2 (SFL-) Always Below 1 Ω



j.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R6-1 (SFL+) - R6-2 (SFL-) Always 1 MΩ or higher
R6-1 (SFL+) - Body ground Always 1 MΩ or higher
R6-2 (SFL-) - Body ground Always 1 MΩ or higher




OK

3.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK CENTER AIRBAG SENSOR
a.
C146259C37
0.76,0.229 0.99,0.385 0.229,0.156 10 false *1 1.906,1.313 2.083,1.49 0.177,0.177 10 false *2 1.01,0.667 1.146,0.833 0.135,0.167 10 false D 1.135,0.656 1.271,0.823 0.135,0.167 10 false C 1.656,0.427 1.885,0.583 0.229,0.156 10 false A
*1 Side Squib LH
*2 Center Airbag Sensor


Connect the connectors to the front seat airbag LH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1825, B1826, B1827 or B1828 is not output.


HINT:

Codes other than DTC B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.




OK

NG