Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY › 2015.06–2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261096 FRONT SEAT SIDE AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT SEAT SIDE AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

·

If the side airbag was deployed, replace the front seat side airbag assembly, separate type front seatback spring assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

for Manual Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY)

for Power Seat: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY)

for Walk in Seat Type: (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>DISASSEMBLY)



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side. (for Manual Seat, Power Seat)

·

The procedure listed below is for the RH side. (for Walk in Seat Type)



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 71910A 2.REMOVE FRONT SEAT HEADREST ASSEMBLY

Hide 72128A 3.REMOVE FRONT SEAT INNER TRACK BRACKET COVER LH

Hide 72124 4.REMOVE FRONT SEAT OUTER TRACK BRACKET COVER LH

Hide 72158 5.REMOVE INNER SEAT TRACK BRACKET COVER LH

Hide 72138B 6.REMOVE SEAT TRACK COVER LH

Hide 72127A 7.REMOVE FRONT SEAT INNER TRACK BRACKET COVER RH (for Walk in Seat Type)

Hide 72123A 8.REMOVE FRONT SEAT OUTER TRACK BRACKET COVER RH (for Walk in Seat Type)

Hide 72157A 9.REMOVE INNER SEAT TRACK BRACKET COVER RH (for Walk in Seat Type)

Hide 72137B 10.REMOVE SEAT TRACK COVER RH (for Walk in Seat Type)

Hide 71706 12.REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)

Hide 71706B 13.REMOVE FRONT SEATBACK BOARD CLIP (w/ Seatback Board)

Hide 73920A 14.DISCONNECT FRONT SEAT SIDE AIRBAG ASSEMBLY

a.

w/o Seatback Board:

i.
B239173

Remove the rubber band from the seat cushion spring.



b.

for Manual Seat, Power Seat:

i.
B239174E01
1.399,3.041 1.579,3.234 0.180,0.193 10 *1 1.601,3.135 1.767,3.135 1.767,3.135 2.519,2.984 false

Detach the claw and disconnect the airbag connector.

Text in Illustration
*1 Fastening Tape


ii.

Detach the 3 airbag wire harness clamps.


iii.

Detach the fastening tape and open the cover.


iv.

Disconnect the airbag wire harness.



c.

for Walk in Seat Type:

i.
B241196

Remove the rubber band from the seat cushion spring.


ii.
B241198E01
1.817,2.955 1.997,3.134 0.179,0.179 10 *1 2.018,3.028 2.11,3.028 false 2.11,3.028 2.375,2.536 false

Detach the claw and disconnect the airbag connector.

Text in Illustration
*1 Fastening Tape


iii.

Detach the 4 airbag wire harness clamps.


iv.

Detach the fastening tape and open the cover.


v.

Disconnect the airbag wire harness.



Hide 15.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

HINT:

Use the same procedure for the RH and LH sides.


a.
B241810

w/ Seat Heater System:

i.

Disconnect the seat heater connector and detach the wire harness clamp.



b.

w/o Seatback Board:

i.
B333273

Remove the 3 hog rings.


ii.

Open the 2 fasteners, and then open the front seatback cover.

B242232E01
0.93,0.011 1.160,0.204 0.230,0.193 10 *A 4.37,0.011 4.600,0.204 0.230,0.193 10 *B

Text in Illustration
*A for Cloth Seat *B for Leather Seat



c.

w/ Seatback Board:

i.
B357448

Detach the hooks.


ii.
B247933

Remove the 5 hog rings.



d.
B239201

Remove the nut and front seatback cover bracket.


e.
B239198

Using a screwdriver, detach the 4 claws to remove the 2 front seat headrest supports.


f.

Remove the separate type seatback cover with pad.


Hide 73920A 16.REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY

CAUTION:

When storing the front seat side airbag assembly, keep the airbag deployment side facing upward.


HINT:

Use the same procedure for the RH and LH sides.


a.
B251815

Detach the 2 clamps.


b.
B333276

Remove the 2 nuts and front seat side airbag assembly.

CAUTION:
·

The nuts must not be reused.

·

Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.