Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit supplies power to the driving support ECU assembly when the ignition switch is ON.

WIRING DIAGRAM

C385207E01
0.813,0.906 2.052,1.115 1.24,0.208 10 false from IG Circuit 2.688,1.104 3.719,1.333 1.031,0.229 10 false ECU-IG NO. 1 5.063,0.792 5.281,0.99 0.219,0.198 10 false 7 5.333,0.906 5.552,1.104 0.219,0.198 10 false B 5.323,1.948 5.823,2.135 0.5,0.188 10 false GND 5.01,1.792 5.281,2 0.271,0.208 10 false 28 4.99,2.656 5.49,2.844 0.5,0.188 10 false G224 4.99,2.844 7.01,3.094 2.021,0.25 10 false Driving Support ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
A380143C73
1.594,0.198 1.979,0.427 0.385,0.229 1.26,0.958 0.896,0.354 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.625,0.219 2.083,0.417 0.458,0.198 10 false G224 0.781,0.25 0.938,0.448 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the G224 driving support ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G224-7 (B) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Reconnect the G224 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)
a.
A380143C74
1.594,0.198 1.979,0.427 0.385,0.229 2.281,1.813 2.479,1.281 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.635,0.219 2.094,0.417 0.458,0.198 10 false G224 1.958,1.74 2.344,1.948 0.385,0.208 10 false GND
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the G224 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G224-28 (GND) - Body ground Always Below 1 Ω



c.

Connect the G224 driving support ECU assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR