Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM T

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  PROBLEM SYMPTOMS TABLE  


HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.

·

The pre-crash safety system uses the CAN communication system. First, confirm that there are no malfunction in the CAN communication system. Refer to How to Proceed with Troubleshooting.



Pre-Crash System
Symptom Suspected Area Link
"Pre-Crash Safety Unavailable" is displayed Millimeter wave radar sensor assembly front radar incorrect axis gap (vertical) history* Click here
Perform millimeter wave radar sensor assembly adjustment Click here
Millimeter wave radar sensor assembly temperature malfunction Click here
Millimeter wave radar sensor assembly low voltage malfunction Click here
Millimeter wave radar sensor assembly Click here
Combination meter assembly Click here
Driving support ECU assembly Click here
"Pre-Crash System Unavailable Clean Sensor" is displayed Foreign matter attached to millimeter wave radar sensor assembly -
Millimeter wave radar sensor assembly Click here
Combination meter assembly Click here
Driving support ECU assembly Click here
"Forward Camera System Unavailable" is displayed Check current condition of forward recognition camera based on related Data List items.
·

Abnormal forward recognition camera voltage

·

Forward recognition camera temperature outside of operational range

·

Other forward recognition camera malfunction


Click here
Forward recognition camera Click here
Combination meter assembly Click here
Driving support ECU assembly Click here
"Forward Camera System Unavailable Clean Windshield" is displayed The forward recognition camera or windshield glass within the field of view of the forward recognition camera is dirty or fogged up -
Forward recognition camera Click here
Combination meter assembly Click here
Driving support ECU assembly Click here
Although there is possibility of collision, pre-crash controls (all controls) do not operate ("Pre-Crash Safety Unavailable" is not displayed) Check if pre-crash safety system is canceled -
Vehicle condition/environment does not match the pre-crash safety system operation conditions (Confirm control operation conditions). Click here
Check installation condition of millimeter wave radar sensor assembly Click here
Perform millimeter wave radar sensor assembly adjustment Click here
Millimeter wave radar sensor assembly Click here
Check installation condition of forward recognition camera Click here
Perform forward recognition camera adjustment Click here
Forward recognition camera Click here
Driving support ECU assembly Click here
Although there is no possibility of collision, pre-crash controls (all controls) operate Vehicle condition/environment does not match the pre-crash safety system operation conditions (Confirm control operation conditions). Click here
Check installation condition of millimeter wave radar sensor assembly Click here
Perform millimeter wave radar sensor assembly adjustment Click here
Millimeter wave radar sensor assembly Click here
Check installation condition of forward recognition camera Click here
Perform forward recognition camera adjustment Click here
Forward recognition camera Click here
Driving support ECU assembly Click here
Pre-crash safety system does not operate Check if pre-crash safety system is canceled -
ECU power source circuit Click here
Driving support ECU assembly Click here
Pre-crash safety system cannot be canceled (PCS warning light does not illuminate) Combination meter assembly (check if indicator illuminates using Active Test) Click here
Driving support ECU assembly Click here
Combination meter assembly Click here

*: When the "Pre-Crash Safety Unavailable" message is displayed and "Front Radar Incorrect Axis Gap (Vertical) History:ON" is output, the millimeter wave radar sensor may be automatically performing beam axis calibration. In this case, the display is turned off due to beam axis adjustment being performed.

Automatic calibration is complete when the "Pre-Crash Safety Unavailable" message turns off.

After beam axis adjustment or automatic calibration completes, clear the "Front Radar Incorrect Axis Gap (Vertical) History:ON" history.