Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2017.08
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261257 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Headlight Cleaner Motor and Relay Circuit  


DESCRIPTION

This circuit provides power to the headlight cleaner control relay.

The headlight cleaner control relay sends the signal from the headlight cleaner switch assembly, etc. to the headlight cleaner motor and pump assembly to operate the headlight cleaner system.

WIRING DIAGRAM

B488781E01
0.677,0.698 1.51,0.927 0.833,0.229 10 false form Battery 0.677,1.344 1.51,1.573 0.833,0.229 10 false form Battery 0.219,2.031 1.563,2.271 1.344,0.24 10 false form IG1 NO.1 Relay 2.323,0.917 3,1.115 0.677,0.198 10 false H-LP CLN 2.24,2.208 3.167,2.448 0.927,0.24 10 false ECU-IG NO.2 5.031,3.219 7.052,3.49 2.021,0.271 10 false Headlight Cleaner Control Relay 5.021,3.042 5.479,3.24 0.458,0.198 10 false A38 3.729,1.26 5.24,1.656 1.51,0.396 10 false Headlight Cleaner Motor and Pump Assembly 3.729,1.083 4.188,1.281 0.458,0.198 10 false A37 4.031,0.594 4.188,0.792 0.156,0.198 10 false 2 4.854,0.594 5.01,0.792 0.156,0.198 10 false 1 5.677,0.708 5.99,0.906 0.313,0.198 10 false PB 5.677,2.031 5.99,2.229 0.313,0.198 10 false IG 5.688,2.563 6,2.76 0.313,0.198 10 false E 5.427,0.573 5.583,0.771 0.156,0.198 10 false 6 5.417,1.927 5.573,2.125 0.156,0.198 10 false 3 5.417,2.427 5.573,2.625 0.156,0.198 10 false 4 0.208,3.104 2.042,3.302 1.833,0.198 10 false *1: for 5L-E 2.958,0.594 3.198,0.792 0.24,0.198 10 false *1 2.948,1.24 3.188,1.438 0.24,0.198 10 false *2 2.344,1.552 3.021,1.75 0.677,0.198 10 false H/L CLN 0.208,3.385 1.594,3.656 1.385,0.271 10 false *2: except 5L-E 1.948,1.906 2.188,2.104 0.24,0.198 10 false *1 1.938,2.542 2.177,2.74 0.24,0.198 10 false *2 0.26,2.635 1.521,2.875 1.26,0.24 10 false form IG NO.1 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY
a.

Remove the headlight cleaner motor.

Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>REMOVAL


b.

Inspect the headlight cleaner motor.

Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>INSPECTION



OK

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - BATTERY)

NG

REPLACE HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - BATTERY)
a.
U170629E01
0.189,0.043 0.382,0.203 0.193,0.161 10 *a 0.453,0.948 0.727,1.108 0.274,0.161 10 A37

Disconnect the headlight cleaner motor and pump assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-2 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Headlight Cleaner Motor and Pump Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)
a.
U170626E01
0.177,0.068 0.338,0.233 0.161,0.165 10 *a 2.003,1.027 2.341,0.69 2.341,0.69 2.426,0.69 false 2.443,0.607 2.618,0.758 0.175,0.151 10 IG 1.761,1.698 1.901,1.850 0.140,0.151 10 E 1.505,1.299 1.616,1.792 1.616,1.792 1.737,1.792 false 0.501,1.056 0.794,1.203 0.292,0.147 10 A38

Disconnect the headlight cleaner control relay connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-3 (IG) - Body ground Ignition switch ON 11 to 14 V
A38-3 (IG) - Body ground Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-4 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Headlight Cleaner Control Relay)


OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY)
a.

Disconnect the A38 headlight cleaner control relay connector.


b.

Disconnect the A37 headlight cleaner motor and pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-1 - A38-6 (PB) Always Below 1 Ω
A38-6 (PB) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR