Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: for Automatic Transmission

*2: for Manual Transmission


WIRING DIAGRAM

U170694E04
2.615,1.083 4.396,1.5 1.781,0.417 10 false Park/Neutral Position Switch Assembly*1 5.302,1.25 5.729,1.438 0.427,0.188 10 false H51 5.302,1.438 6.635,1.781 1.333,0.344 10 false Radio and Display Receiver Assembly 2.615,0.927 3.146,1.115 0.531,0.188 10 false C159 0.24,0.594 1.396,0.958 1.156,0.365 10 false from ECU-IG NO.1 Fuse 3.729,0.479 3.99,0.667 0.26,0.188 10 false RL 3.083,0.479 3.344,0.667 0.26,0.188 10 false RB 5.417,0.615 5.75,0.802 0.333,0.188 10 false REV 5.229,0.479 5.365,0.667 0.135,0.188 10 false 2 2.896,0.479 3.031,0.667 0.135,0.188 10 false 2 2.604,2.521 3.844,2.708 1.24,0.188 10 false C41*3, C160*4 4.01,0.49 4.135,0.677 0.125,0.188 10 false 1 4.01,2.042 4.313,2.24 0.302,0.198 10 false 1*3 2.802,2.042 3.042,2.229 0.24,0.188 10 false 2*3 2.594,2.719 4.74,2.906 2.146,0.188 10 false Back-up Light Switch Assembly*2 0.094,3.438 2.073,3.625 1.979,0.188 10 false *2: for Manual Transmission 0.083,3.146 2.063,3.333 1.979,0.188 10 false *1: for Automatic Transmission 2.469,3.156 4.448,3.344 1.979,0.188 10 false *3: for 1GR-FE or 2TR-FE 2.479,3.448 4.458,3.635 1.979,0.188 10 false *4: for 1KD-FTV or 1GD-FTV 2.792,2.26 3.031,2.448 0.24,0.188 10 false 1*4 4,2.26 4.302,2.458 0.302,0.198 10 false 2*4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E278094

Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check] (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>OPERATION CHECK).


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK
Shift Lever Position Display
R ON
Except R OFF

HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.




OK

NG

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
U149192E01
0.067,0.058 0.309,0.243 0.242,0.186 10 *a 1.566,0.492 1.930,0.683 0.364,0.191 10 H51 0.063,0.733 0.392,0.904 0.330,0.171 10 REV 0.944,1.363 0.643,0.82 0.643,0.82 0.459,0.82 false

a.

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H51-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
H51-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)

Result
Result Proceed to
OK A
NG (for Automatic Transmission) B
NG (for Manual Transmission) C



A

B

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

C

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the H51 radio and display receiver assembly connector.


b.

Disconnect the C159 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H51-2 (REV) - C159-1 (RL) Always Below 1 Ω
H51-2 (REV) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U149436E05
1.792,1.01 2.01,0.344 2.01,0.344 2.229,0.344 false 2.281,0.25 2.573,0.458 0.292,0.208 10 false RB 0.26,1.01 0.677,1.24 0.417,0.229 10 false C159 0.042,0 0.333,0.208 0.292,0.208 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C159-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/neutral Position Switch Assembly)

Result
Result Proceed to
OK (for AC60F) A
OK (for A750F) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the H51 radio and display receiver assembly connector.


b.

Disconnect the C41*1 or C160*2 back-up light switch assembly connector.

Measure the resistance according to the value(s) in the table below.

*1: for 1GR-FE or 2TR-FE

*2: for 1KD-FTV or 1GD-FTV


Standard Resistance:
for 1GR-FE or 2TR-FE
Tester Connection Condition Specified Condition
H51-2 (REV) - C41-1 Always Below 1 Ω
H51-2 (REV) - Body ground Always 10 kΩ or higher

for 1KD-FTV or 1GD-FTV
Tester Connection Condition Specified Condition
H51-2 (REV) - C160-2 Always Below 1 Ω
H51-2 (REV) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)
a.
E377460E01
0.083,0.563 0.5,0.813 0.417,0.25 0.083,1.177 0.5,1.427 0.417,0.25 0.052,0.052 0.365,0.25 0.313,0.198 10 false *a 0.167,0.594 0.563,0.771 0.396,0.177 10 false C41 0.125,1.198 0.521,1.375 0.396,0.177 10 false C160 0.594,0.583 0.906,0.781 0.313,0.198 10 false *A 0.604,1.177 0.917,1.375 0.313,0.198 10 false *B

Disconnect the back-up light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1GR-FE or 2TR-FE
Tester Connection Switch Condition Specified Condition
C41-2 - Body ground Ignition switch ON 11 to 14 V


Standard Voltage:
for 1KD-FTV or 1GD-FTV
Tester Connection Switch Condition Specified Condition
C160-1 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*A for 1GR-FE or 2TR-FE
*B for 1KD-FTV or 1GD-FTV
*a Front view of wire harness connector
(to Back-up Light Switch Assembly)


Result
Result Proceed to
OK (for R150F) A
OK (for RA61F) B
OK (for G52F) C
NG D


A

B

C

D

REPAIR OR REPLACE HARNESS OR CONNECTOR