READ DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Actual vehicle speed | - |
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383.75 rpm |
Engine idling: 650 to 750 rpm | - |
| Calculate Load | Load calculated by ECM | Min.: 0%
Max.: 100% |
·
Engine idling: 7 to 26% ·
Running without load (2500 rpm): 10 to 20% |
- |
| Coolant Temp | Engine coolant temperature | Min.: -40°C (-40°F)
Max.: 140°C (284°F) |
After warming up engine: 75 to 90°C (167 to 194°F) | ·
If the value is -40°C (-40°F), the sensor circuit is open. ·
If the value is 140°C (284°F), the sensor circuit is shorted. |
| Ambient Temperature | Ambient temperature | Min.: -40°C (-40°F)
Max.: 215°C (419°F) |
Equivalent to ambient air temperature | - |
| Engine Run Time | Engine run time | Min.: 0 seconds
Max.: 65535 seconds |
Time after engine start | - |
| Battery Voltage | Battery voltage | Min.: 0 V
Max.: 65.535 V |
Engine idling: 11 to 14 V | - |
| Glow Indicator Supported | Status of the glow indicator supported | Unsupp or Supp | - | - |
| Glow Indicator | Status of the glow indicator | ON or OFF | - | - |
| Starter Signal | Starter signal | ON or OFF | ·
ON: Engine cranking ·
OFF: Engine not cranking |
- |
| Neutral Position SW Signal | PNP switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Transfer L4 | Transfer status | ON or OFF | ·
ON: Transfer in L4 ·
OFF: Transfer not in L4 |
- |
| Stop Light Switch | Stop light switch status | ON or OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| Check Mode | Check mode | ON or OFF | ON: Check mode on | - |
| SPD Test Result | Check mode result for vehicle | Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor | Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor | Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor | Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor | Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor | Compl or Incmpl | - | - |
| O2S(A/FS) Heater Monitor | Heated oxygen sensor (air fuel ratio sensor) heater monitor | Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | Heated oxygen sensor (air fuel ratio sensor) heater monitor | Compl or Incmpl | - | - |
| O2S(A/FS) Monitor | Heated oxygen sensor (air fuel ratio sensor) monitor | Not Avl or Avail | - | - |
| O2S(A/FS) Monitor | Heated oxygen sensor (air fuel ratio sensor) monitor | Compl or Incmpl | - | - |
| A/C Monitor | A/C monitor | Not Avl or Avail | - | - |
| A/C Monitor | A/C monitor | Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor | Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor | Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor | Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor | Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor | Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor | Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor | Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor | Compl or Incmpl | - | - |
| # Codes(Include History) | # of Codes | Min.: 0
Max.: 255 |
- | Number of stored DTCs. |
| MIL | MIL status | ON or OFF | OFF | - |
| MIL ON Run Distance | Distance driven after MIL turns on | Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile) |
- | This is the distance driven since the MIL was illuminated. |
| Running Time from MIL ON | Running time after MIL turns on | Min.: 0 minutes
Max.: 65535 minutes |
Equivalent to running time after MIL turns on | - |
| Time after DTC Cleared | Time after DTCs cleared | Min.: 0 minutes
Max.: 65535 minutes |
Equivalent to time after DTCs cleared | - |
| Distance from DTC Cleared | Distance driven after DTCs cleared | Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile) |
Equivalent to distance driven after DTCs cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycles after DTCs cleared | Min.: 0
Max.: 255 |
- | Number of warm-up cycles after DTCs are cleared. |
| OBD Requirements | OBD requirements | - | - | - |
| Number of Emission DTC | Emissions-related DTCs | Min.: 0
Max.: 127 |
- | - |
| TC and TE1 | TC and TE1 terminals of DLC3 | ON or OFF | - | Active Test support data. |
| Total Distance Traveled | Total Distance Traveled | Min.: 0 km
Max.: 16777215 km (10425361 mile) |
- | - |
| Model Code | Model code | - | - | - |
| Transmission (Engine) Type | Transmission type | - | - | - |
| Cylinder Number | Cylinder number | - | - | - |
| Transmission Type | Transmission type | - | - | - |
| Destination | Destination | - | - | - |
| Model Year | Model year | - | - | - |
| System Identification | System identification | - | - | - |
| Accel Position from EFI | Absolute accelerator pedal position | - | - | Value calculated by adding an adjustment value to the actual accelerator pedal position. |
| Injection Volume from EFI | Injection volume | Min.: 0 mm3/st
Max.: 1279.98 mm3/st |
Engine idling: 3.0 to 10 mm3/st | Injection volume received from the ECM. |
| SPD (NT) | Input shaft speed | Min.: 0 rpm
Max.: 12750 rpm |
·
Lock-up ON (after warming up engine): Input turbine speed (NT) equal to engine speed ·
Lock-up OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed |
The data is displayed in increments of 50 rpm. |
| SPD (SP2) | Output shaft speed | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Vehicle stopped: 0 km/h (0 mph)
(output shaft speed equal to vehicle speed) |
- |
| Shift SW Status (P Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (R Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (N Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (N,P Range) Supported | Status of park/neutral position switch (N or P) supported | Supp or Unsupp | - | - |
| Shift SW Status (N,P Range) | Park/neutral position switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
- |
| Sports Shift Up SW | Sport shift up switch status | ON or OFF | ·
ON: Shift lever held in "+" (up-shift) ·
OFF: Shift lever not held in "+" (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status | ON or OFF | ·
ON: Shift lever held in "-" (down-shift) ·
OFF: Shift lever not held in "-" (down-shift) |
- |
| Sports Mode Selection SW | Sport mode select switch status | ON or OFF | ·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
| Shift SW Status (D Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in D, S, "+" or "-" ·
OFF: Shift lever not in D, S, "+" or "-" |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| A/T Oil Temperature 1 | No. 1 ATF temperature sensor value | Min.: -40°C (-40°F)
Max.: 150°C (302°F) |
·
After stall test: Approx. 80°C (176°F) ·
Equal to ambient temperature after cold soak |
If the value is "-40°C (-40°F)" or "150°C (302°F)", the No. 1 ATF temperature sensor circuit is open or shorted. |
| A/T Oil Temperature 2 | No. 2 ATF temperature sensor value | Min.: -40°C (-40°F)
Max.: 150°C (302°F) |
·
After stall test: Approx. 80°C (176°F) ·
Equal to ambient temperature after cold soak |
If the value is "-40°C (-40°F)" or "150°C (302°F)", the No. 1 ATF temperature sensor circuit is open or shorted. |
| ATF Thermal Degradation Estimate | Estimated value of ATF thermal degradation | Min.: 0
Max.: 65535 |
- | If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the ATF. |
| Lock Up | Lock-up | ON or OFF | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Shift Status | TCM gearshift command | 1st, 2nd, 3rd, 4th or 5th | Same as actual gear | - |
| SLT Solenoid Status | Shift solenoid valve SLT status | ON or OFF | ·
ON: Accelerator pedal released ·
OFF: Accelerator pedal depressed |
- |
| SLU Solenoid Status | Shift solenoid valve SLU status | ON or OFF | ·
ON: Shift solenoid valve SLU operating ·
OFF: Shift solenoid valve SLU not operating |
- |
| Snow or 2nd Start Mode | 2nd start mode status | ON or OFF | ·
ON: 2ND START mode on ·
ON: 2ND START mode off |
- |
PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON or OFF | - |
| Activate the Solenoid (SLU) | Operate shift solenoid valve SLU | ON or OFF | [Vehicle Condition]
·
Ignition switch ON ·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SLT)* | Operate shift solenoid valve SLT and raise line pressure | ON or OFF
|
[Vehicle Condition]
·
Vehicle stopped ·
Engine idling |
| Activate the Solenoid (S1) | Operate shift solenoid valve S1 | ON or OFF | [Vehicle Condition]
·
Ignition switch ON ·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (S2) | Operate shift solenoid valve S2 | ON or OFF | [Vehicle Condition]
·
Ignition switch ON ·
Engine stopped ·
Shift lever in P or N |
| Activate the Lock Up | Control shift solenoid valve SLU to set automatic transmission to lock-up | ON or OFF | Possible to check shift solenoid valve SLU operation.
[Vehicle Condition] ·
Vehicle speed: 70 km/h (44 mph) or more ·
Gear: Highest gear ·
Throttle valve opening angle: Less than 20% |
| Control the Shift Position | Operate shift solenoid valves and set each shift position | ·
Press "→" button: Shift up ·
Press "←" button: Shift down |
Possible to check operation of the shift solenoid valves.
[Vehicle Condition] 50 km/h (31 mph) or less |
| Activate the Solenoid (SR) | Operate shift solenoid valve SR | ON or OFF | [Vehicle Condition]
·
Ignition switch ON ·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL1) | Operate shift solenoid valve SL1 | ON or OFF | [Vehicle Condition]
·
Ignition switch ON ·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL2) | Operate shift solenoid valve SL2 | ON or OFF | [Vehicle Condition]
·
Ignition switch ON ·
Engine stopped ·
Shift lever in P or N |
*: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV)>HYDRAULIC TEST) as well. Note that the pressure values in the Active Test and hydraulic test are different.