Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2017.08–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the TCM.

DTC Code DTC Detection Condition Trouble Area
P0705 One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
·

P input signal

·

N input signal

·

NSW input signal

·

R input signal

·

D input signal


(B) Any of the following signals is ON for 2.0 sec. or more with the shift lever in S (2-trip detection logic):
·

P input signal

·

N input signal

·

NSW input signal

·

R input signal


(C) P, R, N, D and NSW switches are OFF simultaneously (2-trip detection logic).
·

Open or short in park/neutral position switch circuit

·

Transmission control switch (transmission floor shift assembly)

·

Park/neutral position switch

·

TCM



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the TCM.

For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the TCM according to the shift lever position (P, R, N, D or S).

The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C251066E04
5.813,6.052 6.198,6.25 0.385,0.198 10 false TCM 4.313,1.552 5.146,1.75 0.833,0.198 10 false to ST Relay 0.208,1.573 1.865,1.823 1.656,0.25 10 false from Ignition Switch (ST1) 0.031,0.594 1.844,1.104 1.813,0.51 10 false Certification ECU (Smart Key ECU Assembly) (STAR) 5.25,5.146 5.563,5.344 0.313,0.198 10 false G70 5.583,5.146 5.896,5.344 0.313,0.198 10 false S 5.302,4.927 5.521,5.125 0.219,0.198 10 false 15 5.25,3.792 5.563,3.99 0.313,0.198 10 false G69 5.594,3.792 5.906,3.99 0.313,0.198 10 false P 5.313,3.573 5.531,3.771 0.219,0.198 10 false 13 5.25,3.198 5.563,3.396 0.313,0.198 10 false G71 5.594,3.208 5.906,3.406 0.313,0.198 10 false R 5.354,3 5.573,3.198 0.219,0.198 10 false 9 5.26,2.604 5.573,2.802 0.313,0.198 10 false G69 5.583,2.594 5.896,2.792 0.313,0.198 10 false N 5.323,2.396 5.542,2.594 0.219,0.198 10 false 14 5.25,2 5.563,2.198 0.313,0.198 10 false G71 5.594,2 5.906,2.198 0.313,0.198 10 false D 5.365,1.802 5.583,2 0.219,0.198 10 false 8 5.25,0.646 5.563,0.844 0.313,0.198 10 false G69 5.583,0.635 6,0.833 0.417,0.198 10 false NSW 5.313,0.438 5.531,0.635 0.219,0.198 10 false 12 3.771,1.688 3.99,1.885 0.219,0.198 10 false 5 3.781,2.115 4,2.313 0.219,0.198 10 false 7 3.771,2.719 3.99,2.917 0.219,0.198 10 false 9 3.781,3.906 4,4.104 0.219,0.198 10 false 6 3.771,3.313 3.99,3.51 0.219,0.198 10 false 1 3.771,5.25 3.99,5.448 0.219,0.198 10 false 7 3.583,1.448 3.802,1.646 0.219,0.198 10 false L 3.5,1.885 3.771,2.083 0.271,0.198 10 false DL 2.135,0.5 2.406,0.698 0.271,0.198 10 false *1 2.156,1.427 2.427,1.625 0.271,0.198 10 false *2 3.5,2.49 3.771,2.688 0.271,0.198 10 false NL 2.771,2.729 3.042,2.927 0.271,0.198 10 false RB 3.5,3.104 3.771,3.302 0.271,0.198 10 false RL 3.5,3.688 3.771,3.885 0.271,0.198 10 false PL 3.583,5.031 3.854,5.229 0.271,0.198 10 false S 2.771,1.427 2.99,1.625 0.219,0.198 10 false B 2.771,5.01 3.042,5.208 0.271,0.198 10 false IG 2.594,1.677 2.813,1.875 0.219,0.198 10 false 4 2.594,3.031 2.813,3.229 0.219,0.198 10 false 2 2.604,5.25 2.875,5.448 0.271,0.198 10 false 3 2.313,5.542 2.625,5.74 0.313,0.198 10 false G47 2.313,5.708 4.167,5.906 1.854,0.198 10 false Transmission Control Switch 0.063,6.448 2.094,6.646 2.031,0.198 10 false *2: w/o Entry and Start System 0.063,6.115 2.073,6.313 2.01,0.198 10 false *1: w/ Entry and Start System 0.219,5.146 1.844,5.344 1.625,0.198 10 false from ECU-IG NO. 1 Fuse 0.229,2.906 1.917,3.104 1.688,0.198 10 false from ECU-IG NO. 1 Fuse 2.313,4.198 2.729,4.396 0.417,0.198 10 false C159 2.313,4.385 4.135,4.583 1.823,0.198 10 false Park/Neutral Position Switch

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the intelligent tester, read the Data List.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status/
ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (P Range) PNP switch status/
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status/
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (N Range) PNP switch status/
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not held in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not held in "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Shift SW Status (D Range) PNP switch status/
ON or OFF
·

ON: Shift lever in D, S, "+" or "-"

·

OFF: Shift lever not in D, S, "+" or "-"


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECU-IG NO. 1 FUSE - PARK/NEUTRAL POSITION SWITCH)
a.
U170314E02
1.76,1.021 2.031,0.344 false 0.125,0.01 0.344,0.25 0.219,0.24 10 false *a 0.5,1.021 0.906,1.198 0.406,0.177 10 false C159 2.073,0.24 2.313,0.427 0.24,0.188 10 false RB

Disconnect the C159 park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C159-2 (RB) - Body ground Ignition switch ON 11 to 14 V
C159-2 (RB) - Body ground Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch)



OK

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
a.
U170315E02
2.052,1.021 2.292,0.323 false 0.052,0 0.271,0.24 0.219,0.24 10 false *a 0.5,1.021 0.854,1.198 0.354,0.177 10 false C159 2.365,0.208 2.604,0.396 0.24,0.188 10 false B

Disconnect the C159 park/neutral position switch connector.


b.

Disconnect the C92 ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C159-4 (B) - Body ground Ignition switch ON 11 to 14 V
C159-4 (B) - Body ground Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch)



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712E94
1.875,0.99 2.208,0.365 false 1.292,0.948 0.917,0.365 false 2.094,1.292 2.458,1.781 false 0.99,1.781 1.333,1.281 false 1.604,0.958 1.521,0.365 false 2.052,1.781 1.958,1.271 false 1.635,1.781 1.719,1.271 false 2.26,0.25 2.573,0.448 0.313,0.198 10 false RL 0.052,0 0.365,0.198 0.313,0.198 10 false *a 0.76,0.25 1.073,0.448 0.313,0.198 10 false B 2.5,1.677 2.813,1.875 0.313,0.198 10 false L 0.729,1.677 1.042,1.875 0.313,0.198 10 false NL 1.25,0.25 1.563,0.448 0.313,0.198 10 false RB 2.094,1.677 2.406,1.875 0.313,0.198 10 false PL 1.375,1.677 1.688,1.875 0.313,0.198 10 false DL

Disconnect the C159 park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever in P Below 1 Ω
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever in N Below 1 Ω
2 (RB) - 7 (DL) Shift lever in D, S, "+" or "-" Below 1 Ω
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever not in R 10 kΩ or higher
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever not in D, S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch)



OK

4.CHECK HARNESS AND CONNECTOR (ECU-IG NO. 1 FUSE - TRANSMISSION CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (ECU-IG NO. 1 FUSE - TRANSMISSION CONTROL SWITCH)
a.
U169949E02
1.813,1.083 2.344,0.635 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.385,0.521 2.698,0.719 0.313,0.198 10 false IG 0.542,1.01 0.917,1.24 0.375,0.229 10 false G47

Disconnect the G47 transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G47-3 (IG) - Body ground Ignition switch ON 11 to 14 V
G47-3 (IG) - Body ground Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)



OK

5.INSPECT TRANSMISSION CONTROL SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT TRANSMISSION CONTROL SWITCH
a.
C203344E14
1.656,0.771 1.125,0.333 true 1.125,1.385 1.656,0.958 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 0.927,0.229 1.167,0.427 0.24,0.198 10 false IG 0.958,1.292 1.146,1.49 0.188,0.198 10 false S

Disconnect the G47 transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - TCM)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - TCM)
a.
U170414E02
1.083,2.063 0.469,2.802 false 1.146,2.073 0.979,2.792 false 1.896,2.073 1.646,2.802 false 1.958,2.073 2.333,2.802 false 2.344,2.063 3.031,2.802 false 2.167,2.833 2.615,3 0.448,0.167 10 false 8 (D) 1.49,2.833 1.917,3 0.427,0.167 10 false 9 (R) 0.76,2.833 1.208,3 0.448,0.167 10 false 13 (P) 0.156,2.833 0.604,3 0.448,0.167 10 false 14 (N) 0.073,0.031 0.438,0.281 0.365,0.25 10 false *a 1.625,0.313 1.906,0.458 0.281,0.146 10 false G71 0.865,0.302 1.146,0.448 0.281,0.146 10 false G69 2.323,0.313 2.625,0.458 0.302,0.146 10 false G70 2.802,2.833 3.25,3 0.448,0.167 10 false 15 (S)

Disconnect all the connectors from the TCM.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G69-13 (P) - Body ground
·

Ignition switch ON

·

Shift lever in P


11 to 14 V
G71-9 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
G69-14 (N) - Body ground
·

Ignition switch ON

·

Shift lever in N


11 to 14 V
G71-8 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D


11 to 14 V
G70-15 (S) - Body ground
·

Ignition switch ON

·

Shift lever in S, "+" or "-"


11 to 14 V
G69-13 (P) - Body ground
·

Ignition switch ON

·

Shift lever not in P


Below 1 V
G71-9 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
G69-14 (N) - Body ground
·

Ignition switch ON

·

Shift lever not in N


Below 1 V
G71-8 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D


Below 1 V
G70-15 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in S, "+" or "-"


Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to TCM)

HINT:

*: The voltage will drop slightly due to the illumination of the back-up light.




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
a.

Disconnect the C159 park/neutral position switch connector.


b.

Disconnect the G69 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-4 (B) - G69-12 (NSW) Always Below 1 Ω
C159-4 (B) - Body ground Always 10 kΩ or higher
G69-12 (NSW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR