Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2017.08–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  U0100  Lost Communication with ECM / PCM "A"  


DESCRIPTION

The ECM communicates with the TCM using the Controller Area Network (CAN).

If there is a problem with this communication, the TCM stores a DTC.

DTC Code DTC Detection Condition Trouble Area
U0100 All conditions are met for 1.25 seconds (1-trip detection logic):
·

Ignition switch is ON.

·

Battery voltage is 10.5 V or higher.

·

There is no communication between the ECM and TCM.


·

Harness or connector

·

ECM

·

TCM



WIRING DIAGRAM

C217589E16
5.823,3.125 6.219,3.323 0.396,0.198 10 false TCM 5.635,1.25 6.135,1.448 0.5,0.198 10 false CAN+ 5.823,2.948 6.125,3.146 0.302,0.198 10 false G70 5.354,1.354 5.635,1.552 0.281,0.198 10 false 21 5.635,2.229 6.135,2.427 0.5,0.198 10 false CAN- 5.354,2.344 5.635,2.542 0.281,0.198 10 false 20 1.865,3.125 2.26,3.323 0.396,0.198 10 false ECM 1.854,2.948 2.396,3.146 0.542,0.198 10 false C92 1.969,1.25 2.469,1.448 0.5,0.198 10 false CAN+ 2.469,1.344 2.75,1.542 0.281,0.198 10 false 24 1.958,2.219 2.458,2.417 0.5,0.198 10 false CAN- 2.469,2.323 2.75,2.521 0.281,0.198 10 false 18

CAUTION / NOTICE / HINT

HINT:
·

Refer to the inspection procedure for the CAN communication system.

·

If the CAN communication malfunctions, the TCM cannot receive current data from the ECM. In this case, the freeze frame data output from the TCM has not been updated so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is an effective way to find malfunctions.

·

The malfunctioning area can be confirmed using the Bus Check function of the GTS.




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - TCM)
a.

Disconnect the C92 ECM connector.


b.

Disconnect the G70 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C92-24 (CAN+) - G70-21 (CAN+) Always Below 1 Ω
C92-18 (CAN-) - G70-20 (CAN-) Always Below 1 Ω
C92-24 (CAN+) or G70-21 (CAN+) - Body ground or other terminals Always 10 kΩ or higher
C92-18 (CAN-) or G70-20 (CAN-) - Body ground or other terminals Always 10 kΩ or higher




OK

2.CHECK IF DTC OUTPUT RECURS (DTC U0100)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK IF DTC OUTPUT RECURS (DTC U0100)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / DTC / Clear.


e.

Replace the TCM (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TCM>REMOVAL).

HINT:

Replace the TCM with the TCM of a normally functioning vehicle of the same model.



f.

Start the engine.


g.

Enter the following menus: Powertrain / ECT / DTC.


h.

Read the DTCs using the GTS.

Result
Result Proceed to
U0100 is output A
DTCs are not output B



A

B