Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1249  Double Locking ECU Communication Stop  


DESCRIPTION

DTC B1249 is stored when communication between the double lock door control relay assembly and main body ECU (multiplex network body ECU) stops for more than 10 seconds.

DTC Code DTC Detection Condition Trouble Area
B1249 Communication between the double lock door control relay assembly and main body ECU (multiplex network body ECU) stops for more than 10 seconds.
·

Double lock door control relay assembly

·

Driver side junction block assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

B489149E01
0.292,2.26 1.948,2.656 1.656,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 0.313,2.083 0.469,2.281 0.156,0.198 10 false A 1.156,0.844 1.771,1.042 0.615,0.198 10 false LIN2 1.573,0.719 1.885,0.917 0.313,0.198 10 false 16 1.552,1.427 2.792,1.781 1.24,0.354 10 false Driver Side Junction Block Assembly 1.563,1.25 1.875,1.448 0.313,0.198 10 false 2N 2.469,0.708 2.781,0.906 0.313,0.198 10 false 13 2.844,1.375 3.667,1.583 0.823,0.208 10 false from Battery 2.854,1.885 3.677,2.094 0.823,0.208 10 false from Battery 5.229,3.125 6.833,3.51 1.604,0.385 10 false Double Lock Door Control Relay Assembly 5.219,2.958 5.677,3.156 0.458,0.198 10 false G212 4.292,2.083 4.969,2.302 0.677,0.219 10 false D/L NO. 2 4.135,1.573 5.177,1.792 1.042,0.219 10 false S-HORN NO. 2 5.646,0.823 6.083,1.031 0.438,0.208 10 false MPX1 5.646,1.396 6.26,1.594 0.615,0.198 10 false CPUB 5.656,1.906 5.969,2.104 0.313,0.198 10 false +B 5.646,2.573 6.104,2.771 0.458,0.198 10 false GND 5.406,0.698 5.563,0.896 0.156,0.198 10 false 9 5.344,1.271 5.573,1.5 0.229,0.229 10 false 11 5.344,1.771 5.573,2 0.229,0.229 10 false 12 5.417,2.458 5.573,2.656 0.156,0.198 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When communication between the double lock door control relay and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1249 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOUBLE LOCK DOOR CONTROL RELAY)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOUBLE LOCK DOOR CONTROL RELAY)
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the G212 double lock door control relay assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - G212-9 (MPX1) Always Below 1 Ω
A-16 (LIN2) or G212-9 (MPX1) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY - BATTERY AND BODY GROUND)

NG

8.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK - DOUBLE LOCK DOOR CONTROL RELAY)
4.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY - BATTERY AND BODY GROUND)
a.
B477436E02
1.521,0.26 1.948,0.49 0.427,0.229 2.188,1.198 2.625,0.781 2.625,0.781 2.802,0.781 true 1.99,1.438 1.656,1.927 1.656,1.927 1.469,1.927 true 2.146,1.427 2.385,1.906 2.385,1.906 2.573,1.906 true 0.052,0.042 0.375,0.271 0.323,0.229 10 false *a 1.573,0.281 2.031,0.479 0.458,0.198 10 false G212 2.656,1.823 2.969,2.021 0.313,0.198 10 false +B 1.021,1.844 1.49,2.063 0.469,0.219 10 false CPUB 2.875,0.698 3.24,0.896 0.365,0.198 10 false GND

Disconnect the G212 double lock door control relay assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G212-7 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G212-12 (+B) - Body ground Always 11 to 14 V
G212-11 (CPUB) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Double Lock Door Control Relay Assembly)


OK

5.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
a.

Temporarily replace the double lock door control relay assembly with a new or normally functioning one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RELAY>REMOVAL).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1249 is not output.




OK

END (DOUBLE LOCK DOOR CONTROL RELAY IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

8.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK - DOUBLE LOCK DOOR CONTROL RELAY)
a.

Disconnect the 2N driver side junction block assembly connector.


b.

Disconnect the G212 double lock door control relay assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2N-13 - G212-9 (MPX1) Always Below 1 Ω
2N-13 - Body ground Always 10 kΩ or higher




OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR