Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2017.08–2020.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

Steering sensor signals are sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering sensor zero point malfunction diagnostic function.

DTC Code DTC Detection Condition Trouble Area
C1432 A steering sensor power supply malfunction signal is received from the steering sensor.
·

ECU-B fuse

·

ECU-IG NO. 1 fuse

·

Steering sensor power supply

·

Steering sensor



WIRING DIAGRAM

C200080E49
3.906,0.833 4.76,1.031 0.854,0.198 10 false from Battery 3.938,1.469 5.031,1.656 1.094,0.188 10 false from IG1 Circuit 0.875,0.813 1.208,1 0.333,0.188 10 false BAT 0.99,1.479 1.177,1.646 0.188,0.167 10 false IG 0.833,1.792 1.198,1.979 0.365,0.188 10 false ESS 1.323,0.625 1.563,0.823 0.24,0.198 10 false 5 1.323,1.26 1.542,1.458 0.219,0.198 10 false 4 1.323,1.625 1.5,1.781 0.177,0.156 10 false 1 0.26,2.542 1.365,2.771 1.104,0.229 10 false Steering Sensor 0.865,3.438 2.802,3.635 1.938,0.198 10 false : CAN Communication System 5.51,2.219 7.125,2.615 1.615,0.396 10 false Skid Control ECU (Master Cylinder Solenoid) 5.51,2.073 5.719,2.271 0.208,0.198 10 false A7 0.229,2.375 0.688,2.542 0.458,0.167 10 false G205 2.073,1.688 3.01,1.854 0.938,0.167 10 false ECU-IG NO. 1 2.26,1.021 2.74,1.208 0.479,0.188 10 false ECU-B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1432, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>U0073).

·

When the speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) has trouble, DTCs for the steering sensor may be stored even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering sensor.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (IG, BAT)
a.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


b.

Disconnect the G205 steering sensor connector.


c.
C266564E06
0.333,1.167 0.802,1.417 0.469,0.25 1.875,1.479 1.635,1.938 true 2.094,1.448 2.708,1.448 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 0.427,1.208 0.813,1.479 0.385,0.271 10 false G205 2.781,1.385 3.177,1.563 0.396,0.177 10 false BAT 1.531,1.958 1.75,2.146 0.219,0.188 10 false IG

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G205-4 (IG) - Body ground Ignition switch ON 11 to 14 V
G205-5 (BAT) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)



OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the G205 steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G205-1 (ESS) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR