Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) › 2017.08–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260766 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV)  P0500  Vehicle Speed Sensor Malfunction  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a pulse signal and outputs it to the TCM via the combination meter. The TCM determines the vehicle speed based on the frequency of this pulse signal.

DTC Code DTC Detection Condition Trouble Area
P0500 While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the TCM (2-trip detection logic).
·

Open or short in speed signal SPD1 circuit

·

Combination meter system

·

TCM



MONITOR DESCRIPTION

The TCM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite this condition being met, the TCM interprets this as a malfunction in the speed signal circuit. The TCM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM

C382758E01
2.917,1.083 6.125,1.281 3.208,0.198 10 false from Skid Control ECU 3.469,2.781 5.458,2.979 1.99,0.198 10 false to Other ECUs 5.333,2.26 5.948,2.458 0.615,0.198 10 false SPD1 5.01,2.427 5.323,2.625 0.313,0.198 10 false 25 5.552,2.948 6.01,3.146 0.458,0.198 10 false G70 5.542,3.115 6,3.313 0.458,0.198 10 false TCM 0.688,2.896 1.188,3.094 0.5,0.198 10 false G304 0.698,3.063 4.677,3.26 3.979,0.198 10 false Combination Meter Assembly 1.604,2.26 1.917,2.458 0.313,0.198 10 false +S 1.958,2.438 2.271,2.635 0.313,0.198 10 false 17 1.635,1.104 1.948,1.302 0.313,0.198 10 false SI 1.958,1.24 2.271,1.438 0.313,0.198 10 false 18

PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

Drive the vehicle.


f.

Read the value displayed on the tester.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -

OK:

Vehicle speed displayed on tester and speedometer display are equal.




OK

NG

2.CHECK COMBINATION METER SYSTEM
2.CHECK COMBINATION METER SYSTEM
a.

Inspect the circuits that send vehicle speed signals to this system in the meter system (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit).


b.

During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.



NEXT

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
a.

Disconnect the G304 combination meter assembly connector.


b.

Disconnect the G70 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G304-17 (+S) - G70-25 (SPD1) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR