Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › from 2017.08
RM27T0E _59 Vehicle Exterior _053749 EXTERIOR PANELS / TRIM _0261299 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS

·

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



PROCEDURE

Hide 52103 1.INSTALL FRONT BUMPER BRACKET SUB-ASSEMBLY LH

a.

Attach the hook to install the front bumper bracket sub-assembly LH.


b.

Install the 2 bolts.


Hide 52102 2.INSTALL FRONT BUMPER BRACKET SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 81110 4.INSTALL HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 53828J 5.INSTALL FRONT FENDER SIDE PANEL PROTECTOR LH

Hide 53827K 6.INSTALL FRONT FENDER SIDE PANEL PROTECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 52521 7.INSTALL FRONT BUMPER CENTER UPPER RETAINER

a.

Install the front bumper center upper retainer with the 4 bolts.


Hide 52116A 8.INSTALL FRONT BUMPER SIDE SUPPORT LH

a.
B488249

Attach the 2 claws to install the front bumper side support LH.


b.

Install the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Install the screw.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 52115A 9.INSTALL FRONT BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure described for the LH side.


Hide 52026B 10.INSTALL FRONT BUMPER NO. 2 EXTENSION SUB-ASSEMBLY LH

a.

Install the front bumper No. 2 extension sub-assembly LH with the 4 bolts.

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)


Hide 52025B 11.INSTALL FRONT BUMPER NO. 2 EXTENSION SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52021 12.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

a.

Install the front bumper reinforcement sub-assembly with the 6 nuts.

Torque:
42.5 N*m (433 kgf*cm, 31 ft.*lbf)


Hide 52129B 13.INSTALL FRONT BUMPER LOWER COVER

a.

Install the front bumper lower cover with the clip.


b.

Install the 5 bolts.


Hide 52618 14.INSTALL FRONT BUMPER LOWER ABSORBER

a.

Attach the 7 claws to install the front bumper energy absorber.


Hide 52119A 15.INSTALL FRONT BUMPER COVER

a.
B488320

w/ Fog Light:

i.

Connect the connector.



b.
B488321

w/ Headlight Cleaner System:

i.

Connect the headlight cleaner hose.



c.
B488319

Attach the 4 claws to install the front bumper cover.

HINT:

Use the same procedure for the RH side.



d.

Remove the protective tape.


e.

Install the 4 clips.


f.
B488243C02
0,0 0,0 false
V100135

Screw
V100136

Bolt
V100137

Clip


Install the 2 clips.


g.

Install the 4 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.

Install the 2 screws.


i.
B488242

Install the 2 screws.

HINT:

Use the same procedure for the screws on the other side.



Hide 53148A 17.INSTALL HEADLIGHT ORNAMENT GARNISH LH (for Halogen Headlight)

Hide 53147A 18.INSTALL HEADLIGHT ORNAMENT GARNISH RH (for Halogen Headlight)

HINT:

Use the same procedure described for the LH side.


Hide 53148A 19.INSTALL HEADLIGHT ORNAMENT GARNISH LH (for LED Headlight)

Hide 53147A 20.INSTALL HEADLIGHT ORNAMENT GARNISH RH (for LED Headlight)

HINT:

Use the same procedure described for the LH side.


Hide 53292A 21.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 22.ADD WINDSHIELD WASHER FLUID (w/ Headlight Cleaner System)

a.

Connect the washer hose and add the windshield washer fluid.


Hide 23.ADJUST FOG LIGHT AIMING (w/ Fog Light)