Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER › from 2017.08
RM27T0E _59 Vehicle Exterior _053749 EXTERIOR PANELS / TRIM _0261300 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 52461F 1.INSTALL REAR BUMPER PAD (for 5 Door)

HINT:
·

When installing the rear bumper pad, heat the rear bumper using a heat light.

·

Use the same procedure for the RH side.



Standard:
Item Temperature
Rear Bumper Cover 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the rear bumper cover excessively.


a.

Clean the rear bumper cover surface.

i.

Using a heat light, heat the rear bumper cover surface.


ii.

Remove the double-sided tape from the rear bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B488290C01
1.833,0.792 1.927,0.406 1.927,0.406 2.281,0.406 true 2.01,1.365 2.104,1.042 2.104,1.042 2.729,1.042 true 2.313,0.323 2.542,0.542 0.229,0.219 10 false *a 2.792,0.958 3.021,1.177 0.229,0.219 10 false *a
*a Mark-off Line


Install 2 new rear bumper pads.

i.

Remove the peeling paper from the face of 2 new rear bumper pads.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.

Align the 2 rear bumper pads with the mark-off line of the rear bumper.


iii.

Install the 2 rear bumper pads.



Hide 52461F 2.INSTALL REAR BUMPER PAD (for 3 Door)

HINT:
·

When installing the rear bumper pad, heat the rear bumper using a heat light.

·

Use the same procedure for the RH side.



Standard:
Item Temperature
Rear Bumper Cover 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the rear bumper cover excessively.


a.

Clean the rear bumper cover surface.

i.

Using a heat light, heat the rear bumper cover surface.


ii.

Remove the double-sided tape from the rear bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.
B488291C01
2.01,0.813 2.542,0.313 2.542,0.313 2.875,0.313 true 2.927,0.229 3.167,0.49 0.24,0.26 10 false *a
*a Mark-off Line


Install a new rear bumper pad.

i.

Remove the peeling paper from the face of a new rear bumper pad.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.

Align the rear bumper pad with the mark-off line of the rear bumper.


iii.

Install the rear bumper pad.



Hide 81920 3.INSTALL REFLEX REFLECTOR ASSEMBLY LH (w/ Reflex Reflector Assembly)

a.

Attach the claw and guide to install the reflex reflector assembly LH.


b.

Install the screw.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 81910 4.INSTALL REFLEX REFLECTOR ASSEMBLY RH (w/ Reflex Reflector Assembly)

HINT:

Use the same procedure described for the LH side.


Hide 81590B 5.INSTALL REAR FOG LIGHT ASSEMBLY LH (w/ Rear Fog Light)

Hide 81580H 6.INSTALL REAR FOG LIGHT ASSEMBLY RH (w/ Rear Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 52046A 7.INSTALL REAR BUMPER PROTECTOR SUB-ASSEMBLY LH

a.

Attach the guide to install the rear bumper protector sub-assembly LH.


b.

Install the grommet.


c.

Install the screw.


Hide 52045A 8.INSTALL REAR BUMPER PROTECTOR SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 89348R 9.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89342 10.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89348S 11.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

HINT:

Use the same procedure described for the rear corner ultrasonic sensor retainer.


Hide 89342A 12.INSTALL REAR CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

HINT:

Use the same procedure described for the rear corner ultrasonic sensor.


Hide 89348D 13.INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

Hide 82163B 14.INSTALL NO. 5 FLOOR WIRE (w/ TOYOTA Parking Assist-sensor System, w/ Rear Fog Light)

a.

Attach the 5 clamps to install the No. 5 floor wire.


b.

Connect the 3 connectors.


Hide 82163B 15.INSTALL NO. 5 FLOOR WIRE (w/ TOYOTA Parking Assist-sensor System, w/o Rear Fog Light)

a.

Attach the 5 clamps to install the No. 5 floor wire.


b.

Connect the 2 connectors.


Hide 82163B 16.INSTALL NO. 5 FLOOR WIRE (w/o TOYOTA Parking Assist-sensor System, w/ Rear Fog Light)

a.

Attach the 2 clamps to install the No. 5 floor wire.


b.

Connect the connector.


Hide 82163A 17.INSTALL NO. 4 FLOOR WIRE (w/ TOYOTA Parking Assist-sensor System, w/ Rear Fog Light)

HINT:

Use the same procedure described for the No. 5 floor wire.


Hide 82163A 18.INSTALL NO. 4 FLOOR WIRE (w/ TOYOTA Parking Assist-sensor System, w/o Rear Fog Light)

HINT:

Use the same procedure described for the No. 5 floor wire.


Hide 82163A 19.INSTALL NO. 4 FLOOR WIRE (w/o TOYOTA Parking Assist-sensor System, w/ Rear Fog Light)

HINT:

Use the same procedure described for the No. 5 floor wire.


Hide 52615 20.INSTALL REAR BUMPER ENERGY ABSORBER

HINT:

When installing the rear bumper energy absorber, heat the rear bumper cover using a heat light.


Standard:
Item Temperature
Rear Bumper Cover 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the rear bumper cover excessively.


a.

When using a new rear bumper cover:

i.

Clean the rear bumper cover surface.


ii.

Using a heat light, heat the rear bumper cover surface.



b.

When reusing the rear bumper cover:

i.

Using a heat light, heat the rear bumper cover surface.


ii.

Remove the double-sided tape from the rear bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



c.

When reusing the rear bumper energy absorber:

i.

Remove the double-sided tape from the rear bumper cover.


ii.

Wipe off any tape adhesive residue with cleaner.


iii.
B493872C01
0.271,0.833 0.271,1.167 0.271,1.167 0.521,1.167 true 1.688,1 1.688,1.333 1.688,1.333 1.938,1.333 true 2.969,0.823 2.969,1.156 true 0.573,1.083 0.885,1.281 0.313,0.198 10 false *a 1.99,1.25 2.302,1.448 0.313,0.198 10 false *a 2.917,1.167 3.229,1.365 0.313,0.198 10 false *a 0.677,2.313 0.99,2.51 0.313,0.198 10 false *b 1.438,2.729 1.75,2.927 0.313,0.198 10 false *c 2.125,2.448 2.438,2.646 0.313,0.198 10 false *d
*a Double-sided Tape
*b 2.0 mm (0.0787 in.)
*c 30 mm (1.18 in.)
*d 50 mm (1.97 in.)


Install the double-sided tape as shown in the illustration.



d.

Install the rear bumper energy absorber.

i.

Remove the peeling paper from the face of the rear bumper energy absorber.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.
B490894

Align the guide and install the rear bumper energy absorber to rear bumper cover as shown in the illustration.

HINT:

Press the rear bumper energy absorber firmly to install it.