Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is stored when a malfunction in the LIN communication bus between the components related to certification is detected continuously 3 times.

DTC Code DTC Detection Condition Trouble Area
B2785 The certification ECU detects a malfunction in the LIN communication bus between components related to certification continuously 3 times.
·

Certification ECU

·

ID code box

·

Steering lock actuator assembly (steering lock ECU)

·

Harness or connector



WIRING DIAGRAM

B489151E01
4.229,0.958 4.844,1.156 0.615,0.198 10 false LIN1 4.24,2.583 4.854,2.781 0.615,0.198 10 false LIN 2.406,0.969 3.021,1.167 0.615,0.198 10 false LIN 1.688,1.521 2.302,1.719 0.615,0.198 10 false G215 1.708,1.708 2.865,1.938 1.156,0.229 10 false Certification ECU 4.146,1.51 4.76,1.708 0.615,0.198 10 false G207 4.156,1.677 5.01,1.875 0.854,0.198 10 false ID Code Box 2.979,3.208 6.375,3.448 3.396,0.24 10 false Steering Lock Actuator Assembly (Steering Lock ECU) 2.979,3.042 3.292,3.24 0.313,0.198 10 false G35 4.01,0.844 4.167,1.042 0.156,0.198 10 false 2 4.031,2.458 4.188,2.656 0.156,0.198 10 false 5 2.76,0.833 2.917,1.031 0.156,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.


HINT:

When DTC B2785 and B2287 are output simultaneously, perform troubleshooting for DTC B2785 first.


PROCEDURE

1.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

DTC B2785 is output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY OR ID CODE BOX)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY OR ID CODE BOX)
a.

Disconnect the G215 certification ECU connector.


b.

Disconnect the G207 ID code box connector.


c.

Disconnect the G35 steering lock actuator assembly (steering lock ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G215-6 (LIN) - G207-2 (LIN1) Always Below 1 Ω
G215-6 (LIN) - G35-5 (LIN) Always Below 1 Ω
G215-6 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Disconnect the G35 steering lock actuator assembly (steering lock ECU) connector.



Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

6.REPLACE STEERING LOCK ACTUATOR ASSEMBLY

DTC B2785 is output

8.CLEAR DTC
6.REPLACE STEERING LOCK ACTUATOR ASSEMBLY
a.

for Manual Tilt and Manual Telescopic Steering Column



b.

for Power Tilt and Power Telescopic Steering Column

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY

i.

Replace the steering lock actuator assembly with a new one.




Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

END (STEERING LOCK ACTUATOR ASSEMBLY IS DEFECTIVE)

DTC B2785 is output

REPLACE CERTIFICATION ECU

8.CLEAR DTC
a.

Disconnect the G207 ID code box connector.



Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

10.REPLACE ID CODE BOX

DTC B2785 is output

REPLACE CERTIFICATION ECU

10.REPLACE ID CODE BOX
a.

Replace the ID code box with a new one.



Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

END (ID CODE BOX IS DEFECTIVE)

DTC B2785 is output

REPLACE CERTIFICATION ECU