Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325853 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Either condition is met:
·

"Main Body" is not displayed on "CAN Bus Check".

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Main body ECU (multiplex network body ECU) CAN branch wire or connector

·

Power source circuit of main body ECU (multiplex network body ECU)

·

Main body ECU (multiplex network body ECU) ground circuit

·

Main body ECU (multiplex network body ECU)

·

Driver side junction block assembly



WIRING DIAGRAM

C382858E02
5.375,6.813 7.083,7.156 1.708,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 3.5,6.771 4.74,7.188 1.24,0.417 10 false Driver Side Junction Block Assembly 5.865,6.125 6.375,6.344 0.51,0.219 10 false GND1 5.896,5.167 6.406,5.385 0.51,0.219 10 false ACC 5.896,3.729 6.406,3.948 0.51,0.219 10 false IG 5.885,2.583 6.396,2.802 0.51,0.219 10 false BECU 5.583,2.583 6.094,2.802 0.51,0.219 10 false A 5.604,3.729 6.115,3.948 0.51,0.219 10 false A 5.573,5.167 6.083,5.385 0.51,0.219 10 false A 5.563,6.135 6.073,6.354 0.51,0.219 10 false A 5.563,5.906 6.073,6.125 0.51,0.219 10 false 11 5.542,4.948 6.052,5.167 0.51,0.219 10 false 29 5.583,3.51 6.094,3.729 0.51,0.219 10 false 32 5.563,2.365 6.073,2.583 0.51,0.219 10 false 30 3.031,2.573 3.542,2.792 0.51,0.219 10 false 2F 3.01,2.333 3.521,2.552 0.51,0.219 10 false 39 2.177,2.396 2.688,2.615 0.51,0.219 10 false ECU-B 0.813,2.563 2.198,2.948 1.385,0.385 10 false from Battery 3,3.74 3.51,3.958 0.51,0.219 10 false 2K 3.042,3.5 3.552,3.719 0.51,0.219 10 false 1 3,4.156 3.51,4.375 0.51,0.219 10 false 2A 3,3.938 3.51,4.156 0.51,0.219 10 false 52 3.01,5.521 3.521,5.74 0.51,0.219 10 false 2A 3.021,5.302 3.531,5.521 0.51,0.219 10 false 48 3.01,6.146 3.521,6.365 0.51,0.219 10 false 2D 3.063,5.865 3.573,6.083 0.51,0.219 10 false 4 0.354,5.521 1.729,5.854 1.375,0.333 10 false from Ignition Switch 0.333,4.177 1.708,4.552 1.375,0.375 10 false from Ignition Switch 0.844,3.698 2.229,4.083 1.385,0.385 10 false from Battery 4.563,3.573 5.51,3.906 0.948,0.333 10 false ECU-IG NO.2 3.76,4.396 4.708,4.729 0.948,0.333 10 false IG1 NO.1 4.917,4.979 5.427,5.198 0.51,0.219 10 false ACC 3.896,5.771 4.406,5.99 0.51,0.219 10 false ACC 5.521,1.063 6.031,1.281 0.51,0.219 10 false G64 5.51,0.479 6.021,0.698 0.51,0.219 10 false G64 5.531,0.26 6.042,0.479 0.51,0.219 10 false 14 5.552,0.823 6.063,1.042 0.51,0.219 10 false 13 5.896,0.469 6.406,0.688 0.51,0.219 10 false CANH 5.896,1.073 6.406,1.292 0.51,0.219 10 false CANL 0.156,1.438 1.385,1.667 1.229,0.229 10 false G294*1, G295*2 0.167,1.625 2.323,2.01 2.156,0.385 10 false No. 3 CAN Junction Connector*1, No. 4 CAN Junction Connector*2 1.646,0.333 1.844,0.531 0.198,0.198 10 false 2 1.635,0.917 1.833,1.115 0.198,0.198 10 false 13 0.625,6.99 2.01,7.375 1.385,0.385 10 false *1: for LHD 0.625,7.323 2.01,7.708 1.385,0.385 10 false *2: for RHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C382885C05
1.5,0.667 1.917,0.917 0.417,0.25 1.844,1.792 2.167,0.833 2.167,0.833 2.333,0.833 false 1.979,1.823 2.323,1 2.323,1 2.49,1 false 1.552,0.708 2.167,0.906 0.615,0.198 10 false G64 2.396,0.74 3.01,0.938 0.615,0.198 10 false CANL 2.563,0.938 3.177,1.135 0.615,0.198 10 false CANH 0.125,0.104 0.74,0.302 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


Disconnect the main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G64-14 (CANH) - G64-13 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Connect the driver side junction block assembly connectors.


c.
C227508C51
1.531,0.552 1.917,0.792 0.385,0.24 2.906,1.073 2.667,0.438 2.667,0.438 2.552,0.438 true 3.094,1.115 3.01,1.594 3.01,1.594 2.875,1.594 true 2.823,1.083 2.646,0.771 2.646,0.771 2.531,0.771 true 1.219,1.083 1.042,0.771 1.042,0.771 0.927,0.771 true 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.667,0.583 1.979,0.74 0.313,0.156 10 false A 2.146,0.375 2.583,0.552 0.438,0.177 10 false BECU 2.219,0.688 2.656,0.865 0.438,0.177 10 false ACC 2.677,1.531 3.115,1.708 0.438,0.177 10 false IG 0.49,0.698 0.969,0.875 0.479,0.177 10 false GND1
*a Component without harness connected
(Driver Side Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-11 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



d.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-30 (BECU) - Body ground Always 11 to 14 V
A-29 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-32 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the driver side junction block assembly connectors.

C382859C01
5.104,1.958 5.521,2.219 0.417,0.26 5.219,0.115 5.635,0.375 0.417,0.26 1.771,0.135 2.188,0.396 0.417,0.26 1.521,1.792 1.938,2.052 0.417,0.26 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.854,0.188 2.167,0.385 0.313,0.198 10 false 2A 5.344,0.177 5.656,0.375 0.313,0.198 10 false 2D 1.625,1.865 1.938,2.063 0.313,0.198 10 false 2F 5.229,2 5.542,2.198 0.313,0.198 10 false 2K
*a Front view of wire harness connector
(to Driver Side Junction Block Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2K-1 - Body ground Always 11 to 14 V
2F-39 - Body ground Always 11 to 14 V
2A-52 - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
2A-48 - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V




OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)