Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325853 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
4WD Control ECU Communication Stop Mode Either condition is met:
·

"Four Wheel Drive Control" is not displayed on "CAN Bus Check".

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "4WD Control ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

4 wheel drive control ECU CAN branch wire or connector

·

Power source circuit of 4 wheel drive control ECU

·

4 wheel drive control ECU ground circuit

·

4 wheel drive control ECU



WIRING DIAGRAM

C382926E01
5.792,0.604 6.406,0.802 0.615,0.198 10 false CANH 1.5,0.625 2.115,0.823 0.615,0.198 10 false G296 4.396,2.177 5.01,2.375 0.615,0.198 10 false 4WD 5.396,0.625 6.01,0.823 0.615,0.198 10 false G53 5.396,1.219 6.01,1.417 0.615,0.198 10 false G53 5.385,2.333 6,2.531 0.615,0.198 10 false G54 5.406,2.969 6.021,3.167 0.615,0.198 10 false G53 5.385,3.729 6,3.927 0.615,0.198 10 false G54 4.333,2.823 4.948,3.021 0.615,0.198 10 false 4WD-B 2.896,2.969 3.948,3.219 1.052,0.25 10 false from Battery 2.458,2.323 3.823,2.594 1.365,0.271 10 false from IG NO.3 Relay 5.792,1.198 6.406,1.396 0.615,0.198 10 false CANL 5.813,2.969 6.427,3.167 0.615,0.198 10 false +B 5.802,2.354 6.417,2.552 0.615,0.198 10 false IG 5.438,3.51 6.052,3.708 0.615,0.198 10 false 10 5.427,2.76 6.042,2.958 0.615,0.198 10 false 21 5.479,2.115 6.094,2.313 0.615,0.198 10 false 4 5.448,0.417 6.063,0.615 0.615,0.198 10 false 20 5.448,1 6.063,1.198 0.615,0.198 10 false 40 5.792,3.75 6.406,3.948 0.615,0.198 10 false GND 5.25,4.427 6.979,4.854 1.729,0.427 10 false 4 Wheel Drive Control ECU 1.5,1.229 2.115,1.427 0.615,0.198 10 false G296 0.75,4.333 1.719,4.531 0.969,0.198 10 false *1: for LHD 0.75,4.615 1.719,4.813 0.969,0.198 10 false *2: for RHD 1.563,0.417 2.177,0.615 0.615,0.198 10 false 2*1 1.521,1.01 2.135,1.208 0.615,0.198 10 false 13*1 0.333,1.615 2.698,1.844 2.365,0.229 10 false No. 5 CAN Junction Connector*1 1.885,0.625 2.5,0.823 0.615,0.198 10 false G297 1.885,1.219 2.5,1.417 0.615,0.198 10 false G297 1.958,0.406 2.573,0.604 0.615,0.198 10 false 3*2 1.927,1 2.542,1.198 0.615,0.198 10 false 14*2 0.333,1.823 2.698,2.052 2.365,0.229 10 false No. 6 CAN Junction Connector*2

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (4 WHEEL DRIVE CONTROL ECU BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U148351C01
0.49,1.01 0.573,1.01 0.573,1.01 0.688,1.344 true 0.448,2 0.542,2 0.542,2 0.688,1.5 true 0.052,0 0.219,0.188 0.167,0.188 10 false *a 0.042,1.906 0.469,2.063 0.427,0.156 10 false CANL 0.094,0.927 0.49,1.083 0.396,0.156 10 false CANH 2.417,1.229 2.719,1.385 0.302,0.156 10 false G53
*a Rear view of wire harness connector
(to 4 Wheel Drive Control ECU)


Disconnect the 4 wheel drive control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-20 (CANH) - G53-40 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the 4 wheel drive control ECU connector.

C382831C02
2.167,0.083 2.604,0.313 0.438,0.229 5.292,0.177 5.729,0.406 0.438,0.229 1.115,1.094 0.979,1.365 0.979,1.365 0.781,1.365 true 5.948,1.073 6.177,1.438 6.177,1.438 6.344,1.438 true 5.969,0.823 6.208,0.5 6.208,0.5 6.375,0.5 true 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 2.25,0.115 2.563,0.313 0.313,0.198 10 false G53 5.396,0.219 5.708,0.417 0.313,0.198 10 false G54 0.542,1.292 0.979,1.49 0.438,0.198 10 false +B 6.396,1.354 6.833,1.552 0.438,0.198 10 false GND 6.427,0.406 6.865,0.604 0.438,0.198 10 false IG
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-10 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G54-21 (+B) - Body ground Always 11 to 14 V
G54-4 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)