Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR(for Front) › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0260997 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  INSTALLATION  


PROCEDURE

Hide 89347B 1.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this step only when necessary.

·

If a front corner ultrasonic sensor retainer has been removed, replace it with a new one. Install the front corner ultrasonic sensor with a new front corner ultrasonic sensor retainer as a set to the front bumper cover.

·

Use the same procedure to install the front corner ultrasonic sensor retainer on the other side.



a.

Clean the front bumper cover surface.

i.

Remove the remaining double-sided tape from the front bumper cover.


ii.

Wipe off any tape adhesive residue with cleaner.



b.
B360651C02
0.76,0.271 1.073,0.427 0.313,0.156 10 false *a 2.521,0.438 2.833,0.594 0.313,0.156 10 false *a
*a 17 mm (0.67 in.)


Cover the sensor installation hole with a 17 mm (0.67 in.) square piece of tape.


c.
B488743C02
1.667,0.792 1.667,0.417 1.667,0.417 2,0.417 false 2.052,0.344 2.365,0.542 0.313,0.198 10 false *a
*a Mark-off Line
V100155

Primer


Using a brush or felt, apply primer or equivalent to the front corner ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the front bumper cover until the primer has dried.




d.

Using a heat light, heat the front bumper cover.

Standard:
Item Temperature
Front Bumper Cover 40 to 60°C (104 to 140°F)


CAUTION:
E306500C01
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper cover excessively.



e.

Peel off the release paper from a new front corner ultrasonic sensor retainer.


f.

Align the front corner ultrasonic sensor retainer with the alignment line and set it on the front bumper cover as shown in the illustration.

NOTICE:

The double-sided tape of a front corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the front corner ultrasonic sensor retainer with a new one when reattachment is necessary.


HINT:
·

Align the connector side with the protrusion of the mark and install it.

·

Press the front corner ultrasonic sensor retainer with a force of 30 N (3.0 kgf) for 3 seconds and install the front corner ultrasonic sensor retainer firmly so that there is no clearance between the front corner ultrasonic sensor retainer and front bumper cover.



B488744C01
2.344,0.948 2.708,1.125 false 1.302,0.417 1.771,0.333 false 1.177,1.229 1.521,1.031 false 2.76,1.073 3.073,1.229 0.313,0.156 10 false *c 1.833,0.25 2.146,0.406 0.313,0.156 10 false *b 1.021,1.208 1.333,1.365 0.313,0.156 10 false *a
*a Alignment Line *b Connector Side
*c Protrusion of the mark - -



Hide 89341K 2.INSTALL FRONT CORNER ULTRASONIC SENSOR

NOTICE:

When reusing the ultrasonic sensor, make sure that each ultrasonic sensor is returned to its original position.


HINT:

Use the same procedure to install the front corner ultrasonic sensor on the other side.


a.

Attach the 2 claws to install the front corner ultrasonic sensor.


b.

Connect the connector.


Hide 89347C 3.INSTALL FRONT CENTER ULTRASONIC SENSOR RETAINER

HINT:

Use the same procedure described for the front corner ultrasonic sensor retainer.


Hide 89341L 4.INSTALL FRONT CENTER ULTRASONIC SENSOR

HINT:

Use the same procedure described for the front corner ultrasonic sensor.


Hide 52119A 5.INSTALL FRONT BUMPER COVER