Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261036 POWER DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  B1243  GSW Terminal Circuit Malfunction  


DESCRIPTION

If the collision door lock release function does not operate normally, or an open or short in the GSW input circuit of the main body ECU (multiplex network body ECU) is detected, DTC B1243 will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1243 GSW Terminal Circuit Malfunction A malfunction occurs in the GSW input circuit of the main body ECU (multiplex network body ECU).
·

Main body ECU (multiplex network body ECU)

·

Driver side junction block assembly

·

Airbag sensor assembly

·

Harness or connector



WIRING DIAGRAM

B345030E43
1.25,0.938 1.708,1.135 0.458,0.198 10 false GSW 1.667,0.833 1.979,1.031 0.313,0.198 10 false 18 0.583,1.802 1.042,2 0.458,0.198 10 false G1 0.594,1.969 2.198,2.271 1.604,0.302 10 false Airbag sensor Assembly 5.646,0.938 6.104,1.135 0.458,0.198 10 false GSW 3.865,0.823 4.573,1.042 0.708,0.219 10 false 25*1, 46*2 5.406,0.823 5.719,1.021 0.313,0.198 10 false 46 3.833,1.344 4.615,1.573 0.781,0.229 10 false 2A*1, 2O*2 4.302,1.5 5.375,2.042 1.073,0.542 10 false Driver Side Junction Block Assembly 5.344,1.802 5.656,2 0.313,0.198 10 false A 5.344,1.979 7,2.531 1.656,0.552 10 false Main Body ECU (Multiplex Network Body ECU) 0.167,2.448 1.677,2.635 1.51,0.188 10 false *1: for 5L-E 1.281,2.438 2.792,2.625 1.51,0.188 10 false *2: except 5L-E

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When DTC B1243 is output, the collision door lock release, shift-linked automatic door lock/unlock and speed-sensitive automatic door lock functions are prohibited.

·

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Recheck for DTCs.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR

OK:

DTC B1243 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
U115554C01
2.01,1.094 2.469,0.438 2.469,0.438 2.594,0.438 false 2.615,0.365 2.99,0.521 0.375,0.156 10 false GSW 0.354,1.083 0.563,1.24 0.208,0.156 10 false G1 0.177,0.104 0.344,0.25 0.167,0.146 10 false *a
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

Turning the engine switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



b.

Disconnect the airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


c.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G1-18 (GSW) - Body ground Ignition switch ON 4.3 to 5.5 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - AIRBAG ECU ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - AIRBAG ECU ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Disconnect the 2A*1 or 2O*2 driver side junction block assembly connector.

*1: for 5L-E

*2: except 5L-E



c.

Disconnect the G1 airbag sensor assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5L-E:
Tester Connection Condition Specified Condition
2A-25 - G1-18 (GSW) Always Below 1 Ω
2A-25 or G1-18 (GSW) - Other terminals and body ground Always 10 kΩ or higher

except 5L-E:
Tester Connection Condition Specified Condition
2O-46 - G1-18 (GSW) Always Below 1 Ω
2O-46 or G1-18 (GSW) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPLACE HARNESS OR CONNECTOR

5.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

B490769C01
1.49,1.333 2.083,1.635 0.594,0.302 3.406,0.167 3.875,0.479 0.469,0.313 5.094,1.271 5.802,1.521 0.708,0.25 3.594,0.26 3.75,0.458 0.156,0.198 10 false A 1.573,1.396 2.125,1.708 0.552,0.313 10 false 2A (*A) 5.198,1.313 5.75,1.625 0.552,0.313 10 false 2O (*B)
*A for 5L-E *B except 5L-E


Standard Resistance:
for 5L-E:
Tester Connection Condition Specified Condition
A-46 (GSW) - 2A-25 Always Below 1 Ω

except 5L-E:
Tester Connection Condition Specified Condition
A-46 (GSW) - 2O-46 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY