Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260747 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Clutch Switch Circuit  


DESCRIPTION

While depressing the clutch pedal, the clutch switch sends a signal to terminal D of the ECM. The ECM cancels cruise control when terminal D receives the signal.

WIRING DIAGRAM

E323405E11
5.281,0.958 5.583,1.25 0.302,0.292 10 false 27 5.552,2 5.917,2.167 0.365,0.167 10 false C34 5.677,2.146 6.167,2.417 0.49,0.271 10 false ECM 3.771,0.948 3.885,1.125 0.115,0.177 10 false 2 2.646,0.958 2.76,1.135 0.115,0.177 10 false 1 2.521,1.479 3.833,1.75 1.313,0.271 10 false A43 2.521,1.625 4.167,1.917 1.646,0.292 10 false Clutch Switch Assembly 0.917,1.073 1.792,1.229 0.875,0.156 10 false from IG1 fuse 0.094,0.042 1.177,0.26 1.083,0.219 12 false for 1GR-FE: 5.531,1.073 5.74,1.26 0.208,0.188 10 false D

E323405E10
5.281,0.99 5.583,1.333 0.302,0.344 10 false 15 5.552,2.021 6.083,2.25 0.531,0.229 10 false C91 5.615,2.188 5.948,2.344 0.333,0.156 10 false ECM 3.771,0.969 3.885,1.146 0.115,0.177 10 false 2 2.646,0.99 2.76,1.167 0.115,0.177 10 false 1 2.521,1.5 4,1.75 1.479,0.25 10 false A43*1, r3*2 2.521,1.646 4.25,1.917 1.729,0.271 10 false Clutch Switch Assembly 1,1.083 2,1.396 1,0.313 10 false from IG1 fuse 0.104,0.073 1.188,0.302 1.083,0.229 12 false for 1KD-FTV: 0.156,2.115 1.458,2.427 1.302,0.313 10 false *1: for LHD 0.146,2.448 1.479,2.698 1.333,0.25 10 false *2: for RHD 5.531,1.104 6.167,1.417 0.635,0.313 10 false D

E323405E12
5.281,0.979 5.583,1.25 0.302,0.271 10 false 14 5.552,2.021 6.083,2.25 0.531,0.229 10 false C149 5.677,2.177 6.25,2.417 0.573,0.24 10 false ECM 3.771,0.969 3.885,1.146 0.115,0.177 10 false 2 2.646,0.99 2.76,1.167 0.115,0.177 10 false 1 2.521,1.5 3.917,1.667 1.396,0.167 10 false A43*1, r3*2 2.521,1.646 4.167,2 1.646,0.354 10 false Clutch Switch Assembly 0.969,1.073 1.885,1.302 0.917,0.229 10 false from IG1 fuse 0.094,0.063 1.25,0.333 1.156,0.271 12 false for 1GD-FTV: 0.146,2.031 1.281,2.208 1.135,0.177 10 false *1: for LHD 0.146,2.365 1.365,2.646 1.219,0.281 10 false *2: for RHD 5.531,1.104 5.74,1.292 0.208,0.188 10 false D

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the ECM refer to Service Bulletin.



PROCEDURE

1.INSPECT CLUTCH SWITCH ASSEMBLY
a.

Remove the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)

NG

REPLACE CLUTCH SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)
a.
C326224C20
1.031,0.26 1.49,0.563 0.458,0.302 1.896,0.26 2.354,0.563 0.458,0.302 1.135,0.333 1.542,0.531 0.406,0.198 10 false A43 1.542,0.292 1.854,0.49 0.313,0.198 10 false *A 2.417,0.281 2.729,0.479 0.313,0.198 10 false *B 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 2.083,0.323 2.49,0.521 0.406,0.198 10 false r3
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Clutch Switch Assembly)


Disconnect the A43*1 or r3*2 clutch switch connector.

·

*1: for LHD

·

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (for LHD):
Tester Connection Switch Condition Specified Condition
A43-1 - Body ground Ignition Switch ON 11 to 14 V
A43-1 - Body ground Ignition Switch off Below 1 V


Standard Voltage (for RHD):
Tester Connection Switch Condition Specified Condition
r3-1 - Body ground Ignition Switch ON 11 to 14 V
r3-1 - Body ground Ignition Switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM)
a.

for 1GR-FE

i.

Disconnect the A43 clutch switch connector.


ii.

Disconnect the C34 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-2 - C34-27 (D) Always Below 1 Ω
A43-2 or C34-27 (D) - Body ground Always 10 kΩ or higher




b.

for 1KD-FTV

i.

Disconnect the A43*1 or r3*2 clutch switch connector.

·

*1: for LHD

·

*2: for RHD



ii.

Disconnect the C91 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
A43-2 - C91-15 (D) Always Below 1 Ω
A43-2 or C91-15 (D) - Body ground Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
r3-2 - C91-15 (D) Always Below 1 Ω
r3-2 or C91-15 (D) - Body ground Always 10 kΩ or higher




c.

for 1GD-FTV

i.

Disconnect the A43*1 or r3*2 clutch switch connector.

·

*1: for LHD

·

*2: for RHD



ii.

Disconnect the C149 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
A43-2 - C149-14 (D) Always Below 1 Ω
A43-2 or C149-14 (D) - Body ground Always 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
r3-2 - C149-14 (D) Always Below 1 Ω
r3-2 or C149-14 (D) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR