Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) D

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  OPERATION CHECK  


CHECK ENTRY AND START SYSTEM (for Entry Function) OPERATION


NOTICE:

Make sure that the entry and start system (for Entry Function) has not been canceled before performing this inspection.


a.

Check the entry unlock function (driver door, front passenger door).

i.

Perform a wireless lock operation to lock the door, touch the unlock sensor built into the backside of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door unlocks.


ii.
B485498C01
0.063,0.104 0.521,0.406 0.458,0.302 12 false *A 0.104,2.5 0.5,2.76 0.396,0.26 12 false *B 2.292,1.271 2.604,1.427 0.313,0.156 10 false *a 1.323,3.573 1.635,3.729 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Inspect the entry unlock detection area. Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.7 to 1 m (2.30 to 3.28 ft.) from the vehicle as shown in the illustration and check that the LED (red) of the electrical key transmitter sub-assembly blinks.


iii.

With the system in unlock standby mode, grasp the front door outside handle assembly (for driver door) and check that the door unlocks.

HINT:
·

The system is in unlock standby mode when the electrical key transmitter sub-assembly is in the detection area and the key ID code sent by the electrical key transmitter sub-assembly matches the key ID code stored by the certification ECU (smart key ECU assembly).

·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the door outside handle assembly.

·

Inspect the front passenger door using the same procedure.




iv.
B433958C01
0.106,0.16 0.693,0.303 0.587,0.144 10 *A 2.598,2.05 3.185,2.194 0.587,0.144 10 *a 0.518,4.181 1.105,4.325 0.587,0.144 10 *a 0.106,2.145 0.693,2.288 0.587,0.144 10 *B 2.173,1.461 2.414,2.132 2.414,2.132 2.551,2.132 false 1.237,3.833 0.927,4.263 0.927,4.263 0.773,4.263 false
*A for LHD
*B for RHD
*a Unlock Sensor (Backside)


Check the unlock response sensitivity. With the system in unlock standby mode, touch the area shown in the illustration and check that the door unlocks.

NOTICE:

If the sensor is touched too quickly or released too slowly, the sensor may not react and the door will not unlock.


HINT:

Inspect the front passenger door using the same procedure.




b.
U164417C01
0.106,0.04 0.693,0.184 0.587,0.144 10 *A 1.552,0.304 1.792,0.447 0.240,0.144 10 *a 2.881,2.661 3.093,2.805 0.212,0.144 10 *a 0.106,2.532 0.693,2.676 0.587,0.144 10 *B 1,1.118 1.348,0.396 1.348,0.396 1.486,0.396 false
*A for LHD
*B for RHD
*a Lock Sensor


Check the entry lock function (driver door, front passenger door).

NOTICE:

If the electrical key transmitter sub-assembly is in the vehicle but outside the detection area (on the instrument panel, in the glove box, on the floor) and a door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter sub-assembly will be locked inside the vehicle.


i.

With the door closed and unlocked, touch the lock sensor of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door locks.

HINT:
·

If the door does not lock even when touching the lock sensor, touch it with your palm.

·

Inspect the front passenger door using the same procedure.




ii.
B485498C01
0.063,0.104 0.521,0.406 0.458,0.302 12 false *A 0.104,2.5 0.5,2.76 0.396,0.26 12 false *B 2.292,1.271 2.604,1.427 0.313,0.156 10 false *a 1.323,3.573 1.635,3.729 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a Approximatery 0.3 m (0.984 ft.)


Inspect the entry lock operating range. Hold the electrical key transmitter sub-assembly approximately 0.7 to 1 m (2.30 to 3.28 ft.) below the bottom edge of the door glass and approximately 0.3 m (0.984 ft.) from the vehicle as shown in the illustration, touch the lock sensor and check that the door locks.

HINT:
·

If the door does not lock even when touching the lock sensor, touch it with your palm.

·

As communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the front door outside handle assembly, the door may not lock if the lock sensor is touched with the same hand that is carrying the electrical key transmitter sub-assembly, etc.

·

If the key lock-in prevention function buzzer sounds, radio waves from the indoor electrical key antenna may be leaking from the vehicle.

·

Inspect the front passenger door using the same procedure.

·

The door lock operation cannot be performed more than 3 times consecutively. (w/ Double Locking System)





c.

Check the entry back door open function.

i.
B485491C01
1.906,3.125 2.417,2.906 false 2.469,2.813 2.781,2.969 0.313,0.156 10 false *1 1.771,1.24 2.083,1.396 0.313,0.156 10 false *a
*1 Back Door Opener Switch Assembly (Open Switch)
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Perform a wireless lock operation to lock the doors, operate the open switch of the back door opener switch assembly while carrying the electrical key transmitter sub-assembly and check that the back door opens.


ii.

Inspect the entry back door open operating range. Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and approximately 0.7 to 1 m (2.30 to 3.28 ft.) from the vehicle as shown in the illustration, press the open switch of the back door opener switch assembly and check that the back door opens.



d.

Check the entry back door lock function.

NOTICE:

If the electrical key transmitter sub-assembly is in the vehicle but outside the detection area (on the instrument panel, in the glove box or on the floor) and a back door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter sub-assembly will be locked inside the vehicle.


i.

With the back door closed and unlocked, press the lock switch of the back door opener switch assembly while carrying the electrical key transmitter sub-assembly outside of the vehicle and check that the back door locks.


ii.
B485491C02
1.896,3 2.396,2.667 false 2.49,2.573 2.802,2.729 0.313,0.156 10 false *1 1.781,1.25 2.094,1.406 0.313,0.156 10 false *a
*1 Back Door Opener Switch Assembly (Lock Switch)
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Inspect the entry back door lock operating range. Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and approximately 0.7 to 1 m (2.30 to 3.28 ft.) from the vehicle as shown in the illustration, press the lock switch of the back door opener switch assembly and check that the back door locks.

HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear bumper.

·

If the key lock-in prevention function buzzer sounds, radio waves from the indoor electrical key antenna may be leaking from the vehicle.






f.

Check the key lock-in prevention function (vehicle interior).

NOTICE:

In order to prevent the electrical key transmitter sub-assembly from being locked inside the vehicle, perform this inspection with the window of a door open.


i.

Turn the engine switch off.


ii.

Place the electrical key transmitter sub-assembly on a front or rear seat.


iii.

Close the door, making sure the doors are unlocked.


iv.

Touch a door lock sensor and check that the doors do not lock and the key lock-in prevention function buzzer (external) sounds for approximately 5 seconds.



g.

Check the transmitter battery saving function

i.

Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.


ii.

Check that the entry and start system (for Entry Function) does not operate while in transmitter battery saving mode.

HINT:

To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.




h.

Check the entry cancel function.

i.

Cancel the entry and start system and check that all the functions of the entry and start system (for Entry Function) no longer operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS

HINT:

While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.




i.

Check the answer-back function (hazard warning light flashing and buzzer* sounding).

Entry Operation Hazard Warning Light Wireless Buzzer*
Entry Lock Flashes once Sounds once
Entry Unlock Flashes twice Sounds twice

*: w/ Wireless Door Lock Buzzer Answer-back Function




KEY DIAGNOSTIC MODE (Using GTS)


HINT:

The buzzer sounds in short, repeated beeps for all items except "Overhead + Rear Room"*4. For "Overhead + Rear Room"*4, the buzzer sounds in one long, continuous beep.


HINT:
·

With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the wireless buzzer.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



a.

Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check (Key Diag Mode).


b.

Inspect the appropriate item according to the following table.

Tester Display Inspection Item
[CH1/CH2] Overhead + Driver Side*1 Front door outside handle assembly (electrical key antenna) (for Driver Door)
[CH1] Overhead + Driver Side*1
[CH2] Overhead + Driver Side*1
[CH1/CH2] Overhead + Passenger Side*2 Front door outside handle assembly (electrical key antenna) (for Front Passenger Door)
[CH1] Overhead + Passenger Side*2
[CH2] Overhead + Passenger Side*2
[CH1/CH2] Overhead + Front Room*3 No. 1 indoor electrical key antenna assembly (front floor)
[CH1] Overhead + Front Room*3
[CH2] Overhead + Front Room*3
[CH1/CH2] Overhead + Rear Room*4 No. 2 indoor electrical key antenna assembly (rear floor)
[CH1] Overhead + Rear Room*4
[CH2] Overhead + Rear Room*4
[CH1/CH2] Overhead + Back Door*5 Electrical key antenna (outside luggage compartment)
[CH1] Overhead + Back Door*5
[CH2] Overhead + Back Door*5
[CH1/CH2] Luggage + Back Door (inside)*6 No. 3 indoor electrical key antenna assembly (inside luggage)
[CH1] Luggage + Back Door (inside)*6
[CH2] Luggage + Back Door (inside)*6
[CH1/CH2] Immobiliser Amp*7 Amplifier (engine switch)
[CH1] Immobiliser Amp*7
[CH2] Immobiliser Amp*7

·

[CH1]: Channel 1 is set.

·

[CH2]: Channel 2 is set.

·

[CH1/CH2]: Channel 1 and 2 switch automatically at a specific interval*.

*: If the electrical key transmitter sub-assembly is detected with either channel 1 or 2, the buzzer sounds.



c.

Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the wireless buzzer sounds.

i.
B485498C01
0.063,0.104 0.521,0.406 0.458,0.302 12 false *A 0.104,2.5 0.5,2.76 0.396,0.26 12 false *B 2.292,1.271 2.604,1.427 0.313,0.156 10 false *a 1.323,3.573 1.635,3.729 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


*1: Front door outside handle assembly (for Driver door)

HINT:
·

Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly in the position shown in the illustration.

·

*2: Perform the same inspection for the front passenger side.





d.
B485492C01
0.573,1.125 2.417,0.25 2.417,0.25 2.75,0.25 false 1.896,1.104 2.417,0.25 false 2.792,0.167 3.104,0.365 0.313,0.198 10 false *a
*a Inspection Point


*3: No. 1 indoor electrical key antenna assembly (front floor)

HINT:

Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.



e.
B485493C01
0.656,0.979 2.5,0.25 2.5,0.25 2.75,0.25 false 2.052,0.948 2.5,0.25 false 2.781,0.177 3.094,0.375 0.313,0.198 10 false *a
*a Inspection Point


*4: No. 2 indoor electrical key antenna assembly (rear floor)

HINT:

Place the electrical key transmitter sub-assembly on the rear seat cushion.



f.
B485494C01
1.927,1.313 2.24,1.51 0.313,0.198 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


*5: Electrical key antenna (outside luggage compartment)

HINT:

Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle as shown in the illustration.



g.
B485495C01
1.354,1.802 2.5,0.333 2.5,0.333 2.75,0.333 false 1.99,1.25 2.5,0.333 false 2.802,0.25 3.115,0.448 0.313,0.198 10 false *a
*a Inspection Point


*6: No. 3 indoor electrical key antenna assembly (inside luggage)

HINT:

Place the electrical key transmitter sub-assembly on the luggage room floor.



h.
B485496C01
2.292,0.917 2.51,0.479 2.51,0.479 2.646,0.479 false 0.656,0.292 0.823,0.292 0.823,0.292 1.125,0.771 false 0.49,0.229 0.802,0.385 0.313,0.156 10 false *1 2.698,0.417 3.01,0.573 0.313,0.156 10 false *2
*1 Engine Switch
*2 Electrical Key Transmitter Sub-assembly


*7: Amplifier (engine switch)

HINT:

While facing the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the transmitter near the engine switch.