Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Entry Exterior Alarm and Answer-back Buzzer do not Sound  


DESCRIPTION

The entry and start system (for Entry Function) uses the wireless door lock buzzer to perform various vehicle exterior warnings. When the conditions of each warning are met, the certification ECU (smart key ECU assembly) sends a buzzer activation request signal to the main body ECU (multiplex network body ECU) via CAN communication and the buzzer sounds.

WIRING DIAGRAM

B325985E45
0.708,1.583 1.104,1.958 0.396,0.375 10 false 2 0.531,2.073 0.896,2.385 0.365,0.313 10 false A39 1.906,1.573 2.167,1.865 0.26,0.292 10 false 1 0.531,2.25 2.333,2.552 1.802,0.302 10 false Wireless Door Lock Buzzer 2.313,1.563 2.74,1.854 0.427,0.292 10 false 30 3.802,1.688 4.385,2.104 0.583,0.417 10 false BZR 2.167,3.375 2.552,3.615 0.385,0.24 10 false 2M 2.958,2.5 3.479,2.854 0.521,0.354 10 false A 3.542,1.573 3.813,1.833 0.271,0.26 10 false 21 2.958,2.677 4.604,3.198 1.646,0.521 10 false Main Body ECU (Multiplex Network Body ECU) 2.167,3.542 5.042,3.896 2.875,0.354 10 false Driver Side Junction Block Assembly 5.271,2.833 7.094,3.229 1.823,0.396 10 false Combination Meter Assembly 0.927,4.125 2.844,4.469 1.917,0.344 10 false : CAN Communication Line 0.896,1.677 1.292,2.052 0.396,0.375 10 false E 1.719,1.688 2.115,2.063 0.396,0.375 10 false B

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to entry and start system (for Entry Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

*: w/ Door Control Battery

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION



PROCEDURE

1.CHECK CUSTOMIZE SETTING (WIRELESS BUZZER RESP) (w/ Wireless Door Lock Buzzer Answer-back Function)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Customize Setting / Wireless Door Lock.


Result:
Result Proceed to
"ON" is displayed A
"OFF" is displayed B



A

2.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

B

2.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

3.READ VALUE USING GTS (EACH UNLOCK DETECTION SWITCH)

B

3.READ VALUE USING GTS (EACH UNLOCK DETECTION SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

OK:

The GTS display changes correctly in response to the lock/unlock operation.


Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal UNLOCK or LOCK UNLOCK: Front door RH unlocked
LOCK: Front door RH locked
-
FL Door Lock Pos Front door LH unlock detection switch signal UNLOCK or LOCK UNLOCK: Front door LH unlocked
LOCK: Front door LH locked
-
RR-Door Lock Pos SW* Rear door RH unlock detection switch signal ON or OFF ON: Rear door RH unlocked
OFF: Rear door RH locked
-
RL-Door Lock Pos SW* Rear door LH unlock detection switch signal ON or OFF ON: Rear door LH unlocked
OFF: Rear door LH locked
-
Back Door Lock Pos SW Back door unlock detection switch signal ON or OFF ON: Back door unlocked
OFF: Back door locked
-

*: for 5 Door



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

4.PERFORM ACTIVE TEST USING GTS (WIRELESS BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform Active Test according to the display on the GTS.

Main Body
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -


Result:
Result Proceed to
Wireless buzzer does not sound A
Wireless buzzer sounds B



A

5.CHECK WIRELESS DOOR LOCK BUZZER

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK WIRELESS DOOR LOCK BUZZER
a.

Disconnect the A39 wireless door lock buzzer connector.


b.

Perform the Active Test using the GTS and sound the wireless door lock buzzer.

Main Body
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -


c.
B222362C59
1.5,0.427 1.865,0.698 0.365,0.271 2.104,1.875 1.802,1.385 false 1.208,1.885 1.552,1.375 false 0.24,0.198 0.552,0.396 0.313,0.198 10 false *a 1.552,0.469 1.865,0.667 0.313,0.198 10 false A39 1.104,1.906 1.375,2.104 0.271,0.198 10 false B 2.094,1.906 2.25,2.104 0.156,0.198 10 false E
*a Front view of wire harness connector
(to Wireless Door Lock Buzzer)


While performing the Active Test, measure the voltage between the terminals of the wireless door lock buzzer.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-1 (B) - A39-2 (E) Active Test Wireless Buzzer ON Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)
Active Test Wireless Buzzer OFF Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE WIRELESS DOOR LOCK BUZZER

NG

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the 2M driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-1 (B) - A-30 (BZR) Always Below 1 Ω
A39-2 (E) - Body ground Always Below 1 Ω
A39-1 (B) or A-30 (BZR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

7.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2M driver side junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-1 (B) - 2M-30 (BZR) Always Below 1 Ω
A39-1 (B) or 2M-30 (BZR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR