Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260991 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.

The navigation receiver assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



DTC Code DTC Detection Condition Trouble Area
B15C2 A difference between the GPS speed and SPD pulse is detected.
·

Meter/gauge system

·

Harness or connector

·

Navigation receiver assembly



WIRING DIAGRAM

E280956E44
1.771,1.052 2.083,1.25 0.313,0.198 10 false +S 2.052,0.938 2.365,1.135 0.313,0.198 10 false 17 1.042,1.813 1.479,2.052 0.438,0.24 10 false G304 1.052,2 3.073,2.271 2.021,0.271 10 false Combination Meter Assembly 4.979,0.917 5.292,1.115 0.313,0.198 10 false 17 5.219,1.063 5.74,1.292 0.521,0.229 10 false SPD 5.094,1.844 5.573,2.083 0.479,0.24 10 false H56 5.073,2.01 7,2.219 1.927,0.208 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

HINT:

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK VEHICLE SENSOR (OPERATION CHECK)
a.
E276610

Enter the "System Sensors Check" screen. Refer to Check GPS & Vehicle Sensors in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Navigation Receiver Type)>OPERATION CHECK).


b.

While driving the vehicle, compare the "Speed" indicator to the reading on the speedometer. Check if these readings are almost equal.

OK:

The readings are equal or almost equal.




OK

NG

2.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135C83
1.479,0.438 1.896,0.656 0.417,0.219 1.073,1.313 0.979,0.49 0.979,0.49 0.813,0.49 true 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.521,0.469 1.917,0.719 0.396,0.25 10 false G304 2.792,3.594 3.188,3.865 0.396,0.271 10 false GND 1.125,3.875 1.521,4.146 0.396,0.271 10 false A 0.594,0.396 0.906,0.594 0.313,0.198 10 false +S
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


ii.

Connect an oscilloscope to terminal G304-17 (+S) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G304-17 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration arrows.





OK

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the H56 navigation receiver assembly connector.


b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-17 (SPD) - G304-17 (+S) Always Below 1 Ω
H56-17 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR