Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System) › from 2017.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261038 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly) via CAN communication system. The certification ECU (smart key ECU assembly) sends door lock/unlock commands to the main body ECU (multiplex network body ECU).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1242 Wireless Door Lock Tuner Circuit Malfunction One of the following conditions is met:
·

Short in RDAM between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short in RCO between the certification ECU (smart key ECU assembly) and door control receiver.


·

Door control receiver

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

B490773E01
5.177,2.833 6.688,3.188 1.51,0.354 10 false Certification ECU (Smart Key ECU Assembly) 4.875,2.219 6.385,2.573 1.51,0.354 10 false G215 5.313,2.219 6.823,2.573 1.51,0.354 10 false E 5.271,1.521 5.823,1.74 0.552,0.219 10 false RDAM 4.875,1.615 6.385,1.969 1.51,0.354 10 false G214 4.865,0.927 6.375,1.281 1.51,0.354 10 false G214 6.01,1.25 6.563,1.469 0.552,0.219 10 false +B 5.958,0.542 6.51,0.76 0.552,0.219 10 false 5V 5.271,0.823 5.823,1.042 0.552,0.219 10 false RCO 4.938,0.74 5.49,0.958 0.552,0.219 10 false 18 4.969,1.427 5.521,1.646 0.552,0.219 10 false 20 4.958,2.031 5.51,2.25 0.552,0.219 10 false 11 1.875,0.833 2.427,1.052 0.552,0.219 10 false +5 2.135,0.823 2.688,1.042 0.552,0.219 10 false 8*1, 4*2 2.125,1.51 2.677,1.729 0.552,0.219 10 false 2*1, 5*2 1.688,1.521 2.24,1.74 0.552,0.219 10 false DATA 1.75,2.208 2.302,2.427 0.552,0.219 10 false GND 2.167,2.083 2.948,2.344 0.781,0.26 10 false 12*1, 1*2 0.781,2.823 2.281,3 1.5,0.177 10 false Door Control Receiver 0.698,2.667 2.208,3.021 1.51,0.354 10 false R41*1, R17*2 0.24,3.177 1.74,3.354 1.5,0.177 10 false *1: for 12 Pin Type 0.229,3.448 1.729,3.625 1.5,0.177 10 false *2: except 12 Pin Type

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the certification ECU (smart key ECU assembly) is replaced, refer to the Service Bulletin.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and start function and wireless control function performance may be affected.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

This DTC is not stored within 10 seconds of the engine switch being turned from on (IG) to off.

·

for 12 Pin Type:

When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

·

for 12 Pin Type:

It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver if the door control receiver has been replaced.




PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the R41*1 or R17*2 door control receiver connector.

*1: for 12 Pin Type

*2: except 12 Pin Type



b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B343405C28
5.083,0.333 5.49,0.542 0.406,0.208 3.302,0.333 3.708,0.542 0.406,0.208 6.021,1.292 6.5,2.083 6.5,2.083 6.667,2.083 true 3.479,1.302 3.823,2.083 3.823,2.083 3.99,2.083 true 3.292,1.292 3.073,2.073 3.073,2.073 2.906,2.073 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 3.333,0.365 3.729,0.563 0.396,0.198 10 false G214 5.115,0.354 5.563,0.552 0.448,0.198 10 false G215 6.719,2 7.031,2.198 0.313,0.198 10 false E 4.052,2 4.365,2.198 0.313,0.198 10 false RCO 2.469,1.979 2.99,2.167 0.521,0.188 10 false RDAM
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition
G214-20 (RDAM) - G215-11 (E) Always 11 to 14 V
G214-18 (RCO) - G215-11 (E) Always Pulse generation at regular intervals
(Below 1 V ←→ 4.5 to 5.5 V)


Standard Resistance:
Tester Connection Condition Specified Condition
G215-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the R41*1 or R17*2 door control receiver connector.

*1: for 12 Pin Type

*2: except 12 Pin Type



b.

Disconnect the G214 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 12 Pin Type:
Tester Connection Condition Specified Condition
R41-2 (DATA) - G214-20 (RDAM) Always Below 1 Ω
R41-8 (+5) - G214-18 (RCO) Always Below 1 Ω
R41-12 (GND) - Body ground Always Below 1 Ω
R41-2 (DATA) or G214-20 (RDAM) - Other terminals and body ground Always 10 kΩ or higher
R41-8 (+5) or G214-18 (RCO) - Other terminals and body ground Always 10 kΩ or higher

except 12 Pin Type:
Tester Connection Condition Specified Condition
R17-5 (DATA) - G214-20 (RDAM) Always Below 1 Ω
R17-4 (+5) - G214-18 (RCO) Always Below 1 Ω
R17-1 (GND) - Body ground Always Below 1 Ω
R17-5 (DATA) or G214-20 (RDAM) - Other terminals and body ground Always 10 kΩ or higher
R17-4 (+5) or G214-18 (RCO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR