1. BEFORE REGISTRATION
The transmitter ID is written on the tire pressure warning valve and transmitter. It is not possible to read the transmitter ID after installing the tire onto the wheel. Therefore, make a note of the transmitter ID before installing the tire.
Tire pressure warning ECU and receiver ID registration after replacement must be performed using the GTS.
In case of tire pressure warning ECU and receiver replacement:
Before replacing, use the GTS to read and record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.
If reading the stored transmitter IDs is impossible due to malfunctions of components such as the tire pressure warning ECU and receiver, remove the tires from the wheels and check the IDs located on the tire pressure warning valve and transmitters.
In case of tire pressure warning valve and transmitter replacement:
Take a note of the 7-digit number (transmitter ID) written on the tire pressure warning valve and transmitter.
| *1 | Tire Pressure Warning Valve and Transmitter | - | - |
| *a | Transmitter ID (7-digit Number) | *b | Wheel Speed Type Tire Inflation Pressure Display Function Identification Mark |
For vehicles equipped with the wheel speed type tire inflation pressure display function, be sure to use tire pressure warning valve and transmitters with identification marks.
2.REGISTER TRANSMITTER ID (USING GTS)
The previously registered IDs will be cleared from memory when the registration is completed.
If the ID registration step is not completed within 300 seconds, ID registration will be canceled.
Set the tire pressure to the specified value.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Utility / ID Registration/Tire Number Registration.
Perform the procedure displayed on the GTS.
The number of tires with transmitters can be changed to 4 wheels only when the default value is set to 5 wheels. The number of tires is changed only when there is a special request from the customer. Normally, the default value for the number of tires is set.
3. CONFIRMATION OF TRANSMITTER ID REGISTRATION (USING GTS)
It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121 to C2124 (C2121 to C2125: w/ Spare Tire).
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121
If the transmitter IDs have not been registered, DTC C2171 is stored in the tire pressure warning ECU and receiver after 3 minutes or more.
If normal pressure values are displayed, the transmitter IDs have been registered correctly.
If the tire pressure values are not displayed after a few minutes, the transmitter IDs may be incorrect or the system may have a malfunction.
After all transmitter IDs are registered, DTC C2126 is stored in the tire pressure warning ECU and receiver and the tire pressure warning light blinks for 1 minute and then illuminates. When the tire pressure warning ECU and receiver successfully receives signals from all the transmitters whose IDs are stored in the ECU, DTC C2126 is cleared and the tire pressure warning light goes off.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 5 Tire Inflation Pressure | ID5 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | ·
If N/A is displayed, data has not been received.* ·
w/ Spare Tire |
*: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121 to C2124 (C2121 to C2125: w/ Spare Tire).
The wheel position cannot be determined from ID1 through ID4 or ID1 through ID5 (w/ Spare Tire) on the Data List.
Reduce the tire inflation pressure of each tire 40 kPa (0.4 kgf/cm2, 5.8 psi) or more, and check that the "ID Tire Inflation Pressure" data is updated and that the actual tire inflation pressures are displayed.
After confirming that all of the tire inflation pressure values have been updated, adjust the tire inflation pressure to the specified value, press the tire pressure warning reset switch and perform initialization.
4.REGISTER TRANSMITTER ID (USING AUTOMATIC ID REGISTRATION FUNCTION)
If the automatic ID registration operation is canceled while registration is being performed, DTC C2126 is stored in the tire pressure warning ECU and receiver.
If the automatic ID registration operation is canceled while registration is being performed and restarted while DTC C2126 is detected, DTC C2126 and C2128 is stored in the tire pressure warning ECU and receiver.
If DTC C2128 is output to the tire pressure warning ECU and receiver during automatic registration, the tire pressure warning light illuminates after blinking for 1 minute.
When all of IDs have been registered to the tire pressure warning ECU and receiver, all the data from the tire pressure warning valve and transmitter is sent to the tire pressure warning ECU and receiver, DTC C2128 is cleared and the tire pressure warning light turns off.
If another tire pressure warning valve and transmitter belonging to the same system is installed to a tire other than the one transmitter registration is being performed on, automatic ID registration does not complete.
When registration is complete, all previously registered IDs are cleared.
Registration mode cannot be accessed even if registration work is performed while DTCs C2176, C2179 and U0129 are output.
Registration mode cannot be accessed even if registration work is performed while the ECU Data List is being displayed using the GTS.
If the ECU Data List is displayed using the GTS while work is being performed, the registration mode will be canceled.
If DTCs C2176, C2179 and U0129 are output while work is being performed, registration mode will be canceled.
If the ignition switch is turned off before starting to drive while performing work, registration mode will be canceled.
Adjust the tire pressure in all tires to the specified pressure.
Turn the ignition switch off and stop the vehicle for 15 minutes or more.
After stopping the vehicle for 15 minutes or more, the frequency of electrical wave signals sent by the tire pressure warning valve and transmitters increases for the first few minutes of driving (8 times the normal frequency).
Press the tire pressure warning reset switch turned on and off 3 times within 3 seconds (pressed → released → pressed → released → pressed → released).
The tire pressure warning ECU and receiver switches to ID registration mode according to the automatic ID registration function.
w/ Tire Inflation Pressure Display Function:
Then a message will be displayed on multi-information display. When registration is being performed, the tire pressure warning light will blink for approximately 1 minute then illuminate and "- -" will be displayed for the inflation pressure of each tire on the multi-information display.
w/o Tire Inflation Pressure Display Function:
The tire pressure warning light will blink for approximately 1 minute then illuminate.
Drive at approximately 37 km/h (23 mph) for approximately 10 to 30 minutes during 1 trip.
During the procedure, make 2 or more right or left turns.
Do not drive the vehicle in reverse during registration.
If the vehicle is driven in reverse during registration, the information may be reset before registration completes, and registration may take longer than normal to complete.
When registration is completed, the tire pressure warning light turns off, the normal tire pressure is displayed on the multi-information display.
Registration may take longer than normal in the following driving environments.
Vehicle is often stopped
Vehicle is stopped for long period of time
Vehicle is driven in reverse
Vehicle is driven parallel to another vehicle with the same type of tire pressure warning valve and transmitter installed for a long duration of time
Vehicle was not stopped for 15 minutes or more before registration
Vehicle was driven at 37 km/h (23 mph) or less for a long duration of time
The ignition switch is turned from ON to off during ID registration
5. TIRE POSITION IDENTIFICATION (USING GTS) (w/ Tire Inflation Pressure Display Function)
Set the tire pressure to the specified value.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 5 Tire Inflation Pressure | ID5 tire inflation pressure | min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | ·
If N/A is displayed, data has not been received.* ·
w/ Spare Tire |
*: It may take a few minutes until the values are displayed.
The wheel position cannot be determined from ID1 through ID5 (w/ Spare Tire) on the Data List.
Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.
It may take a few minutes until the values are displayed.
When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.
Read the "ID Tire Inflation Pressure" value and identify the tire with reduced pressure, and recordthe corresponding tire pressure warning valve and transmitter (ID1 to ID4 or ID5 (w/ Spare Tire)).
Repeat for each tire.
Set the tire pressure to the specified value.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Tire Position Write.
Perform the procedure displayed on the GTS.
6. TIRE POSITION IDENTIFICATION (NOT USING GTS) (w/ Tire Inflation Pressure Display Function)
Set the tire pressure to the specified value.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Perform initialization to clear the existing tire position information, then drive the vehicle at 40 km/h (25 mph) or more for 10 to 30 minutes in 1 trip until each tire position is automatically identified.
Do not drive the vehicle in reverse gear while performing Tire Position Identification. If the vehicle is driven in reverse gear while performing Tire Position Identification, identification information will be discarded and Tire Position Identification may take longer than usual.
When the vehicle is driven under the following conditions, Tire Position Identification may take longer than usual.
The vehicle is stopped frequently.
The vehicle is stopped for a long period of time.
The vehicle is driven in reverse gear.
The vehicle is driven on rough roads or uneven surfaces.