Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2017.08–2020.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260954 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2782  Power Source Control ECU Malfunction  


DESCRIPTION

The certification ECU (smart key ECU assembly) has a power source mode switching function.

This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU (steering lock actuator or upper bracket assembly) is determined to be abnormal.

The steering lock ECU (steering lock actuator or upper bracket assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator or upper bracket assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2782 Power Source Control ECU Malfunction Either of the following conditions is met (1-trip detection logic (Only output while a malfunction is present and the engine switch is on (IG).)):
·

The steering lock motor activation command circuit has a short circuit.

·

The steering lock motor activation command circuit has an open circuit.


HINT:

If the power supply signal from the LIN communication line does not match the power supply signal from the direct line, the system is determined to be malfunctioning.


·

Steering lock ECU (steering lock actuator or upper bracket assembly)

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


DTC Output Confirmation Operation:

Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P* and the engine switch off. The steering unlocks when the engine switch is turned on (ACC) or on (IG) while carrying the electrical key transmitter sub-assembly.)



*: for Automatic Transmission


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. Prohibits the engine from being started.

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2782 -

WIRING DIAGRAM

C382194E03
1.531,0.344 1.823,0.521 0.292,0.177 10 false IGE 1.479,2.052 1.813,2.24 0.333,0.188 10 false GND 1.896,0.219 2.031,0.385 0.135,0.167 10 false 3 1.906,1.938 2.042,2.104 0.135,0.167 10 false 1 0.156,2.5 0.49,2.688 0.333,0.188 10 false G35 0.156,2.656 2.844,3.021 2.688,0.365 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 0.896,3.385 2.583,3.573 1.688,0.188 10 false : LIN Communication Line 6,0.333 6.396,0.521 0.396,0.188 10 false SLR+ 5.708,0.219 5.917,0.406 0.208,0.188 10 false 24 5.552,2.458 6.031,2.646 0.479,0.188 10 false G215 5.552,2.604 7.083,2.979 1.531,0.375 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)
a.
C380739C04
0.344,2.885 1.698,3.052 1.354,0.167 1.573,4.042 2.417,4.208 0.844,0.167 2.313,2.948 2.719,3.083 0.406,0.135 0.177,0.917 0.563,1.125 0.385,0.208 1.042,1.906 1.896,1.104 true 2.844,2 2.292,1.094 true 2.573,2.938 3,2.594 3,2.594 1.615,2.875 true 2.073,4.417 2.073,4.208 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 0.25,0.938 0.594,1.146 0.344,0.208 10 false G35 0.885,1.99 1.25,2.208 0.365,0.219 10 false IGE 2.74,2.031 3.135,2.24 0.396,0.208 10 false GND 3.073,2.51 3.323,2.74 0.25,0.229 10 false *b 3.031,4.042 3.396,4.292 0.365,0.25 10 false GND 1.99,4.469 2.188,4.667 0.198,0.198 10 false *c 0.198,2.323 0.51,2.521 0.313,0.198 10 false *d
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
*b Steering Lock Motor not Operating
*c Steering Lock Motor Operating
*d Waveform


Using an oscilloscope, check the waveform.

OK:
Item Content
Tester Connection G35-3 (IGE) - G35-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Any door opened when conditions below met, and then steering lock motor activated:
·

Shift lever in P*

·

Steering lock unlocked in advance by carrying electrical key transmitter sub-assembly and turning engine switch on (IG)

·

After above conditions met, engine switch turned off


Specified Condition Pulse generation
(See waveform)


*: for Automatic Transmission


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the electrical key transmitter sub-assembly and turn the engine switch on (ACC) or on (IG).

-

To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.

*: for Automatic Transmission






Result:
Proceed to
OK
NG



OK

2.CLEAR DTC AND DATA LIST MALFUNCTION RECORD

NG

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
2.CLEAR DTC AND DATA LIST MALFUNCTION RECORD
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.



f.

Turn the engine switch off.


g.

Disconnect the cable from the negative (-) battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) battery terminal to clear the record of malfunctions stored in the Data List.

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Perform the DTC output confirmation operation.


b.

Check if DTC B2782 is output.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
DTC B2782 is not output. A
DTC B2782 is output. B



A

SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the G35 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-3 (IGE) - G215-24 (SLR+) Always Below 1 Ω
G35-1 (GND) - Body ground Always Below 1 Ω
G35-3 (IGE) or G215-24 (SLR+) - Other terminals and body ground Always 10 kΩ or higher


NOTICE:

If the result is not as specified, check for looseness in the connection which leads to ground.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR