Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260954 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Steering Lock does not Lock  


DESCRIPTION

The steering lock ECU (steering lock actuator or upper bracket assembly) activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little, as is done for a vehicle with a mechanical key, to change the position of the lock hole.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Steering Lock does not Lock
Entry&Start
·

Lock Request Receive

·

S Code Check

·

L Code Check

·

Steering Lock


Main Body
·

FR Door Courtesy SW (for RHD)

·

FL Door Courtesy SW (for LHD)


Power Source Control
·

Shift P Signal



WIRING DIAGRAM

C382196E02
0.875,1.802 1.219,1.979 0.344,0.177 10 false LIN1 2.375,2.438 2.656,2.604 0.281,0.167 10 false LIN 5.375,1.813 5.656,1.979 0.281,0.167 10 false LIN 0.167,2.646 0.677,2.823 0.51,0.177 10 false G207 0.177,2.813 1.76,3.156 1.583,0.344 10 false ID Code Box (Immobiliser Code ECU) 0.708,5.26 2.396,5.448 1.688,0.188 10 false : LIN Communication Line 1.542,4.365 2.094,4.531 0.552,0.167 10 false G215 1.531,4.521 3.365,4.885 1.833,0.365 10 false Certification ECU (Smart Key ECU Assembly) 5.188,4.469 5.531,4.646 0.344,0.177 10 false G35 5.188,4.625 6.99,5.177 1.802,0.552 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 2.271,3.344 2.656,3.531 0.385,0.188 10 false SLR+ 5.375,3.333 5.667,3.521 0.292,0.188 10 false IGE 5.365,3.979 5.719,4.167 0.354,0.188 10 false GND 5.375,0.354 5.531,0.521 0.156,0.167 10 false B 4.396,0.531 5.24,0.719 0.844,0.188 10 false STRG LOCK 3.073,0.333 3.917,0.521 0.844,0.188 10 false from Battery 1.292,1.635 1.448,1.833 0.156,0.198 10 false 2 2.76,2.26 2.917,2.458 0.156,0.198 10 false 6 2.76,3.208 2.969,3.406 0.208,0.198 10 false 24 5.156,0.208 5.302,0.396 0.146,0.188 10 false 7 5.146,1.625 5.292,1.813 0.146,0.188 10 false 5 5.146,3.198 5.292,3.385 0.146,0.188 10 false 3 5.156,3.844 5.302,4.031 0.146,0.188 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), refer to the Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Lock request signal received state OK or NG OK: Lock request signal received for 10 seconds of any of the doors being opened with shift lever in P* and engine switch off.
NG: Except above
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.

*: for Automatic Transmission


OK:

Within 10 seconds of any of the doors being opened with shift lever in P (for Automatic Transmission) and engine switch off, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (S CODE CHECK)

NG

10.READ VALUE USING GTS (DOOR COURTESY SW)
2.READ VALUE USING GTS (S CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

"OK" is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (L CODE CHECK)

NG

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
3.READ VALUE USING GTS (L CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

"OK" is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator or upper bracket assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - POWER SUPPLY AND BODY GROUND)

NG

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - POWER SUPPLY AND BODY GROUND)
a.
C350526C50
1.5,0.917 1.927,1.156 0.427,0.24 0.917,1.813 1.25,2.427 true 2.531,1.813 2.198,2.427 true 0.188,0.135 0.5,0.292 0.313,0.156 10 false *a 1.594,0.948 1.969,1.219 0.375,0.271 10 false G35 0.729,1.604 1.094,1.802 0.365,0.198 10 false GND 2.5,1.615 2.76,1.823 0.26,0.208 10 false B
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Disconnect the steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G35-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)
a.

Reconnect the steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C380739C06
0.344,2.885 1.698,3.052 1.354,0.167 1.573,4.042 2.417,4.208 0.844,0.167 2.313,2.948 2.719,3.083 0.406,0.135 0.177,0.917 0.563,1.125 0.385,0.208 1.042,1.906 1.896,1.104 true 2.844,2 2.292,1.094 true 2.573,2.938 3,2.594 3,2.594 1.615,2.875 true 2.073,4.417 2.073,4.208 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 0.25,0.938 0.594,1.146 0.344,0.208 10 false G35 0.885,1.99 1.25,2.208 0.365,0.219 10 false IGE 2.74,2.031 3.135,2.24 0.396,0.208 10 false GND 3.073,2.51 3.323,2.74 0.25,0.229 10 false *b 3.031,4.042 3.396,4.292 0.365,0.25 10 false GND 1.99,4.469 2.188,4.667 0.198,0.198 10 false *c 0.198,2.323 0.51,2.521 0.313,0.198 10 false *d
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
*b Steering Lock Motor not Operating
*c Steering Lock Motor Operating
*d Waveform


Using an oscilloscope, check the waveform.

OK:
Item Content
Tester Connection G35-3 (IGE) - G35-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Any door opened when conditions below met, and then steering lock motor activated:
·

Shift lever in P*

·

Steering lock unlocked in advance by carrying electrical key transmitter sub-assembly and turning engine switch on (IG)

·

After above conditions met, engine switch turned off


Specified Condition Pulse generation
(See waveform)


*: for Automatic Transmission


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the electrical key transmitter sub-assembly and turn the engine switch on (ACC) or on (IG).

-

To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.

*: for Automatic Transmission






Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the G35 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-3 (IGE) - G215-24 (SLR+) Always Below 1 Ω
G35-3 (IGE) or G215-24 (SLR+) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Reconnect the steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C350527C71
0.427,0.823 0.844,1.083 0.417,0.26 2.583,2.75 1.865,1.979 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 2.542,2.802 3.052,3.063 0.51,0.26 10 false IGE 0.51,0.865 0.823,1.021 0.313,0.156 10 false G35
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G35-3 (IGE) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.

for Power Tilt and Power Telescopic Steering Column:

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY

for Manual Tilt and Manual Telescopic Steering Column:

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY


b.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

"OK" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration again.

HINT:

Refer to the Service Bulletin.



b.

Perform registration.

HINT:

Refer to the Service Bulletin.



c.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

"OK" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

10.READ VALUE USING GTS (DOOR COURTESY SW)
a.

Enter the following menus: Body Electrical / Main Body / Data List.


b.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly RH
(for RHD)
ON or OFF ON: Front door RH open
OFF: Front door RH closed
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part.
FL Door Courtesy SW Front door courtesy light switch assembly LH
(for LHD)
ON or OFF ON: Front door LH open
OFF: Front door LH closed
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part.

OK:

The Data List item changes in accordance with the opening and closing of the driver door.



Result:
Proceed to
OK (for Automatic Transmission)
OK (for Manual Transmission)
NG



OK (for Automatic Transmission)

11.READ VALUE USING GTS (SHIFT P SIGNAL)

OK (for Manual Transmission)

12.READ VALUE USING GTS (STEERING LOCK)

NG

GO TO LIGHTING SYSTEM (DOOR COURTESY SWITCH CIRCUIT)

11.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Move the shift lever to P.


b.

Enter the following menus: Body Electrical / Power Source Control / Data List.


c.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position (P) signal ON or OFF ON: Shift lever in P
OFF: Shift lever not in P
Use this item to determine whether the shift lever position switch (P) is malfunctioning.

OK:

The GTS display changes correctly in response to the shift position.



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (STEERING LOCK)

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (PROBLEM SYMPTOMS TABLE)

12.READ VALUE USING GTS (STEERING LOCK)
a.

Check that the steering is unlocked.


b.

Enter the following menus: Body Electrical / Entry&Start / Data List.


c.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock Steering lock ECU (steering lock actuator or upper bracket assembly) lock confirmation status Unset or Set Unset: Lock not confirmed
Set: Lock confirmed
When Unset is displayed, the steering is not locked.

OK:

"Set" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



b.

Perform registration.

HINT:

Refer to the Service Bulletin.



c.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Lock request signal received state OK or NG OK: Lock request signal received for 10 seconds of any of the doors being opened with shift lever in P* and engine switch off.
NG: Except above
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.

*: for Automatic Transmission


OK:

Within 10 seconds of any of the doors being opened with shift lever in P (for Automatic Transmission) and engine switch off, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)