Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser system compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

The system unsets if these ID codes match. Thus, the certification ECU (smart key ECU assembly) and the ECM communicate with each other enabling the engine to start.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the vehicle engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The immobiliser system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR



HINT:

When the ECM and certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the ECM and certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK FOR DTC

Result:
Result Proceed to
DTCs are not output (for SFI System) A
DTCs are not output (for ECD System) B
DTCs are output C



A

2.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

4.INSPECT ECM (TERMINAL IMI AND IMO)

C

2.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Read the Data List according to the display on the GTS.

Engine and ECT
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut ON or OFF - -

OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK (for 2TR-FE)
OK (for 1GR-FE)
NG



OK (for 2TR-FE)

OK (for 1GR-FE)

NG

3.CHECK WHETHER ENGINE STARTS
3.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT ECM (TERMINAL IMI AND IMO)
4.INSPECT ECM (TERMINAL IMI AND IMO)
a.

Using an oscilloscope, check the waveform.

for Gasoline:
B413963C03
0.927,0.073 1.323,0.302 0.396,0.229 2.115,0.063 2.51,0.292 0.396,0.229 3.344,0.052 3.74,0.281 0.396,0.229 4.656,0.052 5.052,0.281 0.396,0.229 5.802,0.063 6.198,0.292 0.396,0.229 1.313,1.448 1.708,1.677 0.396,0.229 2.677,1.448 3.073,1.677 0.396,0.229 4.219,1.469 4.615,1.698 0.396,0.229 5.469,1.458 5.865,1.688 0.396,0.229 1.406,2.969 1.802,3.198 0.396,0.229 2.094,2.969 2.49,3.198 0.396,0.229 3.198,2.969 3.594,3.198 0.396,0.229 3.885,2.969 4.281,3.198 0.396,0.229 4.594,2.958 4.99,3.188 0.396,0.229 5.354,2.958 5.75,3.188 0.396,0.229 2.5,6.01 2.906,6.01 2.906,6.01 2.906,5.844 true 2.896,8.031 3.302,8.031 3.302,8.031 3.302,7.865 true 4.948,0.833 5.031,1.427 5.031,1.427 5.188,1.427 true 5.052,0.792 5.229,0.177 5.229,0.177 5.396,0.177 true 4.5,2.26 4.583,2.854 4.583,2.854 4.74,2.854 true 4.625,2.229 4.802,1.615 4.802,1.615 4.969,1.615 true 2.458,3.583 2.667,3.156 true 2.208,3.615 1.813,4.333 1.813,4.333 1.646,4.333 true 2.438,3.865 2.5,4.5 2.5,4.5 2.667,4.5 true 2.469,3.74 2.885,4.323 2.885,4.323 3.052,4.323 true 0.958,0.104 1.417,0.302 0.458,0.198 10 false C153 4.688,0.094 5.146,0.292 0.458,0.198 10 false G181 5.833,0.094 6.292,0.292 0.458,0.198 10 false G180 0.083,0.052 0.75,0.25 0.667,0.198 12 false *A (*C) 0.083,2.948 0.542,3.146 0.458,0.198 12 false *B 0.083,0.25 0.542,0.448 0.458,0.198 10 false *a 0.083,1.667 0.542,1.865 0.458,0.198 10 false *a 0.083,3.167 0.542,3.365 0.458,0.198 10 false *a 1.458,3 1.917,3.198 0.458,0.198 10 false G55 2.156,3 2.615,3.198 0.458,0.198 10 false G56 3.26,3 3.719,3.198 0.458,0.198 10 false C34 3.958,3 4.417,3.198 0.458,0.198 10 false C35 4.656,3 5.115,3.198 0.458,0.198 10 false C36 5.417,2.99 5.875,3.188 0.458,0.198 10 false C37 0.875,5.802 1.333,6 0.458,0.198 10 false GND 0.906,7.813 1.365,8.01 0.458,0.198 10 false GND 1,4.542 1.458,4.74 0.458,0.198 10 false *1 1.042,6.521 1.5,6.719 0.458,0.198 10 false *2 1.625,8.427 2.083,8.625 0.458,0.198 10 false *3 2.948,4.823 3.406,5.021 0.458,0.198 10 false *4 2.302,6.792 2.76,6.99 0.458,0.198 10 false *3 3.333,6.781 3.792,6.979 0.458,0.198 10 false *5 2.333,5.917 2.792,6.115 0.458,0.198 10 false *b 3.031,5.917 3.49,6.115 0.458,0.198 10 false *c 2.708,7.948 3.167,8.146 0.458,0.198 10 false *b 3.438,7.927 3.896,8.125 0.458,0.198 10 false *c 2.479,9.25 2.938,9.448 0.458,0.198 10 false *d 4.469,9.25 4.927,9.448 0.458,0.198 10 false *d 2.542,9.531 3,9.729 0.458,0.198 10 false *e 4.385,9.521 4.844,9.719 0.458,0.198 10 false *e 3.583,9.042 4.042,9.24 0.458,0.198 10 false or 5.229,1.344 5.688,1.542 0.458,0.198 10 false IMI 5.448,0.104 5.906,0.302 0.458,0.198 10 false IMO 4.771,2.781 5.229,2.979 0.458,0.198 10 false IMI 5.021,1.531 5.479,1.729 0.458,0.198 10 false IMO 2.583,3 3.208,3.167 0.625,0.167 10 false IMO (*C) 1.167,4.25 1.708,4.448 0.542,0.198 10 false IMI (*C) 2.156,0.104 2.615,0.302 0.458,0.198 10 false C154 3.375,0.094 3.833,0.292 0.458,0.198 10 false C155 1.354,1.479 1.813,1.677 0.458,0.198 10 false C153 2.708,1.479 3.167,1.677 0.458,0.198 10 false C154 4.25,1.5 4.708,1.698 0.458,0.198 10 false G181 5.5,1.49 5.958,1.688 0.458,0.198 10 false G180 0.083,1.469 0.667,1.667 0.583,0.198 12 false *A (*D) 2.729,4.427 3.354,4.594 0.625,0.167 10 false IMO (*D) 3.125,4.25 3.75,4.417 0.625,0.167 10 false IMI (*D)
*A for 2TR-FE *B for 1GR-FE
*C for Automatic Transmission *D for Manual Transmission
*1 Waveform (IMO) *2 Waveform (IMI)
*3 Waveform A *4 Waveform B
*5 Waveform C - -
*a Component with harness connected
(ECM)
*b Approximately 160 ms
*c Approximately 270 ms *d Approximately 40 ms
*e Approximately 60 ms - -


for Diesel:
B492122C01
1.052,0.208 1.385,0.417 0.333,0.208 1.917,0.208 2.25,0.417 0.333,0.208 3.219,0.208 3.552,0.417 0.333,0.208 3.979,0.208 4.313,0.417 0.333,0.208 4.75,0.208 5.083,0.417 0.333,0.208 5.667,0.208 6,0.417 0.333,0.208 0.76,2.083 1.177,2.292 0.417,0.208 1.833,2.083 2.25,2.292 0.417,0.208 2.917,2.083 3.333,2.292 0.417,0.208 3.906,2.083 4.323,2.292 0.417,0.208 4.938,2.083 5.354,2.292 0.417,0.208 5.99,2.083 6.406,2.292 0.417,0.208 2.448,5.031 2.865,5.031 2.865,5.031 2.865,4.865 true 2.844,6.969 3.26,6.969 3.26,6.969 3.26,6.802 true 1.594,1.833 1.76,1.833 1.76,1.833 1.865,1.365 true 2.25,1.833 2.083,1.833 2.083,1.833 1.979,1.365 true 5.583,3.333 5.75,3.333 5.75,3.333 5.792,2.771 true 6.167,3.333 6,3.333 6,3.333 5.885,2.771 true 0.083,0.083 0.427,0.281 0.344,0.198 12 false *A 0.104,2.083 0.427,2.302 0.323,0.219 12 false *B 1.083,3.427 1.396,3.583 0.313,0.156 10 false *1 1.083,5.417 1.396,5.573 0.313,0.156 10 false *2 1.688,7.333 2,7.49 0.313,0.156 10 false *3 2.885,3.885 3.198,4.042 0.313,0.156 10 false *4 3.281,5.74 3.594,5.896 0.313,0.156 10 false *5 0.083,0.25 0.396,0.406 0.313,0.156 10 false *a 2.281,4.938 2.594,5.094 0.313,0.156 10 false *b 2.333,5.333 2.646,5.49 0.313,0.156 10 false *c 2.396,8.177 2.708,8.333 0.313,0.156 10 false *d 4.354,8.448 4.667,8.604 0.313,0.156 10 false *e 2.271,5.74 2.583,5.896 0.313,0.156 10 false *3 2.979,4.938 3.292,5.094 0.313,0.156 10 false *c 0.104,2.26 0.417,2.417 0.313,0.156 10 false *a 0.875,4.813 1.333,5.01 0.458,0.198 10 false GND 0.875,6.75 1.333,6.948 0.458,0.198 10 false GND 3.385,6.885 3.698,7.042 0.313,0.156 10 false *c 2.677,6.875 2.99,7.031 0.313,0.156 10 false *b 4.406,8.188 4.719,8.344 0.313,0.156 10 false *d 2.49,8.438 2.802,8.594 0.313,0.156 10 false *e 3.5,7.969 3.813,8.167 0.313,0.198 10 false or 1.094,0.229 1.469,0.427 0.375,0.198 10 false G57 1.948,0.229 2.323,0.427 0.375,0.198 10 false G58 3.26,0.229 3.635,0.427 0.375,0.198 10 false C90 4.01,0.229 4.385,0.427 0.375,0.198 10 false C91 4.792,0.229 5.167,0.427 0.375,0.198 10 false C92 5.698,0.229 6.073,0.427 0.375,0.198 10 false C93 0.802,2.094 1.25,2.292 0.448,0.198 10 false C149 1.875,2.094 2.323,2.292 0.448,0.198 10 false C150 2.958,2.094 3.406,2.292 0.448,0.198 10 false C151 3.938,2.094 4.385,2.292 0.448,0.198 10 false C152 4.969,2.094 5.417,2.292 0.448,0.198 10 false G184 6.021,2.094 6.469,2.292 0.448,0.198 10 false C185 2.281,1.75 2.656,1.948 0.375,0.198 10 false IMI 1.323,1.75 1.698,1.948 0.375,0.198 10 false IMO 5.302,3.25 5.677,3.448 0.375,0.198 10 false IMO 6.208,3.25 6.583,3.448 0.375,0.198 10 false IMI
*A for 1KD-FTV *B for 1GD-FTV
*1 Waveform (IMO) *2 Waveform (IMI)
*3 Waveform A *4 Waveform B
*5 Waveform C - -
*a Component with harness connected
(ECM)
*b Approximately 160 ms
*c Approximately 270 ms *d Approximately 40 ms
*e Approximately 60 ms - -


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Measurement Condition:
for Gasoline
Item Content
Tester Connection G181-9 (IMO) - Body ground*1
G181-10 (IMI) - Body ground*1
G56-8 (IMO) - Body ground*2
G56-10 (IMI) - Body ground*2
G56-20 (IMO) - Body ground*3
G56-14 (IMI) - Body ground*3
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

for Diesel
Item Content
Tester Connection G58-29 (IMO) - Body ground*4
G58-28 (IMI) - Body ground*4
G185-17 (IMO) - Body ground*5
G185-16 (IMI) - Body ground*5
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected


*1: for 2TR-FE

*2: for 1GR-FE (for Automatic Transmission)

*3: for 1GR-FE (for Manual Transmission)

*4: for 1KD-FTV

*5: for 1GD-FTV



Result:
Result Proceed to
Normal waveform A
Waveform A not output, or has abnormal wavelength or shape B
Waveform B not output, or has abnormal wavelength or shape C
Waveform C not output, or has abnormal wavelength or shape D



A

5.REGISTER ECU COMMUNICATION ID

B

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

C

D

8.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
5.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

8.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the G207 ID code box (immobiliser code ECU) connector.


b.

Disconnect the G56*1, G181*2, G58*3 or G185*4 ECM connector.

*1: for 1GR-FE

*2: for 2TR-FE

*3: for 1KD-FTV

*4: for 1GD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE (for Automatic Transmission)
Tester Connection Condition Specified Condition
G207-4 (EFIO) - G56-10 (IMI) Always Below 1 Ω
G56-10 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1GR-FE (for Manual Transmission)
Tester Connection Condition Specified Condition
G207-4 (EFIO) - G56-14 (IMI) Always Below 1 Ω
G56-14 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 2TR-FE
Tester Connection Condition Specified Condition
G207-4 (EFIO) - G181-10 (IMI) Always Below 1 Ω
G181-10 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV
Tester Connection Condition Specified Condition
G207-4 (EFIO) - G58-28 (IMI) Always Below 1 Ω
G58-28 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV
Tester Connection Condition Specified Condition
G207-4 (EFIO) - G185-16 (IMI) Always Below 1 Ω
G185-16 (IMI) - Body ground Always 10 kΩ or higher
G207-4 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.REGISTER RECOGNITION CODES
9.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 1GR-FE) C
NG (for 1KD-FTV) D
NG (for 1GD-FTV) E
NG (for 1GD-FTV (w/ Urea SCR system)) F



A

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

B

C

D

E

F