Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260992 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: for Automatic Transmission

*2: for Manual Transmission


WIRING DIAGRAM

U170696E03
2.615,1.021 4.396,1.438 1.781,0.417 10 false Park/Neutral Position Switch Assembly*1 5.302,1.198 5.729,1.385 0.427,0.188 10 false H51 5.302,1.365 7,1.76 1.698,0.396 10 false Radio and Display Receiver Assembly 2.615,0.875 3.229,1.063 0.615,0.188 10 false C159 0.594,0.552 1.417,0.896 0.823,0.344 10 false from ECU-IG NO. 1 Fuse 3.729,0.427 3.99,0.615 0.26,0.188 10 false RL 3.083,0.427 3.344,0.615 0.26,0.188 10 false RB 5.417,0.542 5.75,0.729 0.333,0.188 10 false REV 5.219,0.438 5.354,0.625 0.135,0.188 10 false 2 4.448,0.438 4.625,0.625 0.177,0.188 10 false *1 4.708,0.813 4.917,1 0.208,0.188 10 false *4 2.896,0.438 3.031,0.625 0.135,0.188 10 false 2 2.573,2.5 4.021,2.688 1.448,0.188 10 false C41*2, C160*3 4.01,0.438 4.135,0.625 0.125,0.188 10 false 1 4.01,2.021 4.917,2.208 0.906,0.188 10 false 1*2, 2*3 2.5,2.021 3.177,2.208 0.677,0.188 10 false 2*2, 1*3 2.573,2.656 5.25,2.844 2.677,0.188 10 false Back-up Light Switch Assembly*4 0.083,3.385 3.302,3.573 3.219,0.188 10 false *4: for Manual Transmission 0.083,3.115 2.063,3.302 1.979,0.188 10 false *3: for 1KD-FTV or 1GD-FTV 0.083,2.813 2.063,3 1.979,0.188 10 false *2: for 1GR-FE or 2TR-FE 0.083,2.531 2.063,2.719 1.979,0.188 10 false *1: for Automatic Transmission

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E278094

Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>OPERATION CHECK)].


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.




OK

NG

2.CHECK COMBINATION METER ASSEMBLY
2.CHECK COMBINATION METER ASSEMBLY
a.
U170571E01
0.067,0.058 0.309,0.243 0.242,0.186 10 *a 1.547,0.502 1.911,0.692 0.364,0.191 10 H51 0.063,0.75 0.392,0.921 0.330,0.171 10 REV 0.944,1.38 0.643,0.837 0.643,0.837 0.459,0.837 false

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H51-2 (REV) - Body ground Engine switch on (IG), shift lever in R 7.5 to 14 V
H51-2 (REV) - Body ground Engine switch on (IG), shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)

Result
Result Proceed to
OK A
NG (for Automatic Transmission) B
NG (for Manual Transmission) C



A

B

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

C

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the H51 radio and display receiver assembly connector.


b.

Disconnect the C159 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H51-2 (REV) - C159-1 (RL) Always Below 1 Ω
H51-2 (REV) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U170678E02
1.792,1.021 2.01,0.354 2.01,0.354 2.229,0.354 false 2.281,0.26 2.573,0.469 0.292,0.208 10 false RB 0.229,1 0.771,1.208 0.542,0.208 10 false C159 0.042,0 0.333,0.208 0.292,0.208 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C159-2 (RB) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/neutral Position Switch Assembly)

Result
Result Proceed to
OK (for A750F Automatic Transmission) A
OK (for AC60F Automatic Transmission) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the H51 radio and display receiver assembly connector.


b.

Disconnect the C41*1 or C160*2 back-up light switch assembly connector.

*1: for 1GR-FE or 2TR-FE

*2: for 1KD-FTV or 1GD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE or 2TR-FE
Tester Connection Condition Specified Condition
H51-2 (REV) - C41-1 Always Below 1 Ω
H51-2 (REV) - Body ground Always 10 kΩ or higher

for 1KD-FTV or 1GD-FTV
Tester Connection Condition Specified Condition
H51-2 (REV) - C160-2 Always Below 1 Ω
H51-2 (REV) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)
a.
U170758E02
0.177,0.125 0.615,0.396 0.438,0.271 10 false *a 1.5,1.833 1.896,2.031 0.396,0.198 10 false C160 1.99,1.656 2.427,1.927 0.438,0.271 10 false *B 1.552,0.208 1.875,0.406 0.323,0.198 10 false C41 1.99,0.031 2.427,0.302 0.438,0.271 10 false *A

Disconnect the back-up light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1GR-FE or 2TR-FE
Tester Connection Switch Condition Specified Condition
C41-2 - Body ground Engine switch on (IG) 11 to 14 V

for 1KD-FTV or 1GD-FTV
Tester Connection Switch Condition Specified Condition
C160-1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*A for 1GR-FE and 2TR-FE
*B for 1KD-FTV and 1GD-FTV
*a Front view of wire harness connector
(to Back-up Light Switch Assembly)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR