Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (except 5L-E) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0329511 THEFT DETERRENT SYSTEM(except 5L-E) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(except 5L-E)  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B424476E18
0.823,0.156 1.688,0.375 0.865,0.219 10 false from Battery 2.333,1.865 2.948,2.063 0.615,0.198 10 false HORN 1.104,1.094 1.719,1.292 0.615,0.198 10 false HORN 6.115,0.844 6.729,1.042 0.615,0.198 10 false HORN 1.302,2.281 3.406,2.719 2.104,0.438 10 false Engine Room Relay Block 2.573,4.76 3.708,5.125 1.135,0.365 10 false Low Pitched Horn Assembly 4.198,4.75 5.344,5.125 1.146,0.375 10 false High Pitched Horn Assembly 4.438,1.917 6.052,2.323 1.615,0.406 10 false Driver Side Junction Block Assembly 5.375,3.396 7.052,3.927 1.677,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 2.021,0.844 2.24,1.042 0.219,0.198 10 false 1 2.031,1.448 2.25,1.646 0.219,0.198 10 false 3 2.938,0.833 3.156,1.031 0.219,0.198 10 false 2 2.938,1.448 3.156,1.646 0.219,0.198 10 false 5 2.26,4.5 2.479,4.698 0.219,0.198 10 false 1 3.875,4.521 4.094,4.719 0.219,0.198 10 false 1 2.594,4.583 2.948,4.781 0.354,0.198 10 false A24 4.198,4.573 4.552,4.771 0.354,0.198 10 false A25 4.792,4.031 7.104,4.25 2.313,0.219 10 false to Steering Pad Switch Assembly 5.865,0.823 6.219,1.021 0.354,0.198 10 false 28 5.365,3.208 5.719,3.406 0.354,0.198 10 false A 6.74,1.021 7.094,1.219 0.354,0.198 10 false IC 4.625,0.948 4.979,1.146 0.354,0.198 10 false 2M 4.625,1.24 4.979,1.438 0.354,0.198 10 false 21 4.615,1.448 4.969,1.646 0.354,0.198 10 false 2N 4.635,0.75 5.365,0.938 0.729,0.188 10 false 29

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK HORNS OPERATION
a.

Press the steering pad switch assembly and check if the horns sound.


Result:
Proceed to
Horns sound
Horns do not sound



Horns sound

2.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

Horns do not sound

2.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

B490794E01
1.885,0.688 2.229,0.948 0.344,0.26 5.594,0.302 5.938,0.563 0.344,0.26 3.229,1.156 3.542,0.823 true 5.698,0.344 6.01,0.542 0.313,0.198 10 false 2M 2.021,0.74 2.333,0.938 0.313,0.198 10 false A 3.604,0.729 4.281,0.938 0.677,0.208 10 false HORN

Standard Resistance:
Tester Connection Condition Specified Condition
2M-29 - A-28 (HORN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY