Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (except 5L-E) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0329511 THEFT DETERRENT SYSTEM(except 5L-E) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(except 5L-E)  Intrusion Sensor Cancel Switch Circuit  


DESCRIPTION

When the intrusion sensor cancel switch on the map light sub-assembly is pressed, the sensor off signal is sent to the main body ECU (multiplex network body ECU) which causes the intrusion and tilt sensor (theft warning ultrasonic sensor) to stop operating.

WIRING DIAGRAM

B473163E03
5.25,1.958 6.917,2.365 1.667,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 2.146,1.896 3.813,2.302 1.667,0.406 10 false Map Light Assembly 2.01,1.344 3.99,1.521 1.979,0.177 10 false Intrusion Sensor Cancel Switch 5.438,1.115 5.896,1.302 0.458,0.188 10 false SSW1 3.865,1.135 4.323,1.323 0.458,0.188 10 false SOFF 1.5,1.156 1.958,1.344 0.458,0.188 10 false GND3 2.146,1.74 3.813,2.146 1.667,0.406 10 false W7 4.323,1.135 4.781,1.323 0.458,0.188 10 false 26 1.323,1.156 1.781,1.344 0.458,0.188 10 false 5 5.188,1.135 5.646,1.323 0.458,0.188 10 false 13 5.25,1.781 5.708,1.969 0.458,0.188 10 false G216 5.906,0.813 6.365,1 0.458,0.188 10 false +B

CAUTION / NOTICE / HINT

NOTICE:

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS (Intrusion Sens OFF SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sens OFF SW Intrusion sensor cancel switch ON or OFF ON: Intrusion sensor cancel switch on
OFF: Intrusion sensor cancel switch off
-
OK:

The indicator on the GTS switches between ON and OFF in accordance with the intrusion sensor cancel switch status.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT SUB-ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MAP LIGHT SUB-ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the G216 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the W7 map light sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G216-13 (SSW1) - W7-26 (SOFF) Always Below 1 Ω
W7-5 (GND3) - Body ground Always Below 1 Ω
G216-13 (SSW1) or W7-26 (SOFF) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)
a.
E140936E86
0.729,2 0.833,2 0.833,2 1.146,1.583 true 2.083,1.375 2.427,0.813 2.427,0.813 2.542,0.813 true 2.594,0.719 3.208,0.917 0.615,0.198 10 false GND3 0.323,1.917 0.938,2.115 0.615,0.198 10 false SOFF

Remove the map light assembly (intrusion sensor cancel switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Front Door)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
26 (SOFF) - 5 (GND) Intrusion sensor cancel switch not pressed 10 kΩ or higher
26 (SOFF) - 5 (GND) Intrusion sensor cancel switch pressed Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)