Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (for 5L-E) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0329512 THEFT DETERRENT SYSTEM(for 5L-E) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(for 5L-E)  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B488354E03
4.208,4.885 5.385,5.24 1.177,0.354 10 false High Pitched Horn Assembly 4.188,4.698 6.094,4.917 1.906,0.219 10 false A25 2.604,4.729 4.51,4.948 1.906,0.219 10 false A24 2.583,4.906 3.688,5.323 1.104,0.417 10 false Low Pitched Horn Assembly 3.854,4.5 5.76,4.719 1.906,0.219 10 false 1 2.25,4.5 4.156,4.719 1.906,0.219 10 false 1 4.802,4.052 6.938,4.281 2.135,0.229 10 false to Steering Pad Switch Assembly 5.448,3.177 7.104,3.552 1.656,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 4.885,1.938 6.115,2.344 1.229,0.406 10 false Driver Side Junction Block Assembly 1.323,2.302 3.323,2.521 2,0.219 10 false Engine Room Relay Block 2.354,1.885 4.354,2.104 2,0.219 10 false HORN 1.115,1.094 3.115,1.313 2,0.219 10 false HORN 0.781,0.177 2.781,0.396 2,0.219 10 false from Battery 5.927,0.958 6.927,1.146 1,0.188 10 false A 4.688,0.948 5.688,1.135 1,0.188 10 false 2F 4.698,1.458 5.698,1.646 1,0.188 10 false 2D 4.708,1.24 5.708,1.427 1,0.188 10 false 25 4.708,0.698 5.708,0.885 1,0.188 10 false 29 5.885,0.719 6.885,0.906 1,0.188 10 false 28 6.219,0.948 6.875,1.177 0.656,0.229 10 false HORN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HORNS OPERATION
a.

Press the horn switch and check if the horns sound.

Result
Result Proceed to
Horns sound A
Horns do not sound B



A

2.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

B

2.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

B490784E01
1.906,0.625 2.333,0.896 0.427,0.271 5.51,0.406 5.938,0.677 0.427,0.271 3.417,1.156 3.75,0.771 true 2.083,0.708 2.24,0.906 0.156,0.198 10 false A 5.656,0.448 5.948,0.729 0.292,0.281 10 false 2F 3.802,0.646 4.365,0.927 0.563,0.281 10 false HORN

Standard Resistance:
Tester Connection Condition Specified Condition
2F-29 - A-28 (HORN) Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY