Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Multi-display) › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261004 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Multi-display) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Multi-display)  Rear Clearance Sonar Sensor RH Circuit  


DESCRIPTION

The ultrasonic sensor sends and receives ultrasonic waves. Based on the received wave, the sensor calculates the approximate distance between the vehicle and obstacle and sends the distance value as a signal to the clearance warning ECU.

WIRING DIAGRAM

E132021E44
4.375,2 4.688,2.198 0.313,0.198 10 false U7 4.375,2.167 6.01,2.521 1.635,0.354 10 false No. 1 Ultrasonic Sensor (Rear Corner Sensor RH) 1.063,1.99 1.375,2.188 0.313,0.198 10 false U6 1.063,2.156 2.729,2.51 1.667,0.354 10 false No. 1 Ultrasonic Sensor (Rear Center Sensor RH) 2.156,1.635 2.531,1.854 0.375,0.219 10 false EO 2.156,1.25 2.531,1.469 0.375,0.219 10 false SO 4.823,0.813 5.135,1.01 0.313,0.198 10 false BI 4.823,1.635 5.198,1.854 0.375,0.219 10 false EI 4.823,1.25 5.198,1.469 0.375,0.219 10 false SI 2.156,0.813 2.469,1.01 0.313,0.198 10 false BO 2.5,0.74 2.594,0.927 0.094,0.188 10 false 2 2.5,1.146 2.604,1.313 0.104,0.167 10 false 4 4.604,1.521 4.698,1.667 0.094,0.146 10 false 5 4.604,0.74 4.698,0.927 0.094,0.188 10 false 1 4.604,1.146 4.708,1.313 0.104,0.167 10 false 3 2.51,1.521 2.604,1.667 0.094,0.146 10 false 6

PROCEDURE

1.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)
a.

Replace the No. 1 ultrasonic sensor with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).



NEXT

2.CHECK HARNESS AND CONNECTOR (REAR CORNER SENSOR RH - REAR CENTER SENSOR RH)
2.CHECK HARNESS AND CONNECTOR (REAR CORNER SENSOR RH - REAR CENTER SENSOR RH)
a.

Disconnect the U7 No. 1 clearance sensor (rear corner sensor RH) connector.


b.

Disconnect the U6 No. 1 clearance sensor (rear center sensor RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U7-1 (BI) - U6-2 (BO) Always Below 1 Ω
U7-3 (SI) - U6-4 (SO) Always Below 1 Ω
U7-5 (EI) - U6-6 (EO) Always Below 1 Ω
U7-1 (BI) - Body ground Always 10 kΩ or higher
U7-3 (SI) - Body ground Always 10 kΩ or higher
U7-5 (EI) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR