The main body ECU (multiplex network body ECU) controls the front fog light.
Inspect the fuse for circuits related to this system before performing the follow procedure.
w/ Entry and Start System:
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Using the GTS, perform the Active Test.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Fog Light Relay | Front fog lights | OFF or ON | Light control switch in Tail or Head position. |
Front fog lights turn on.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (except 5L-E) | B |
| NG (for 5L-E) | C |
A
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>PROBLEM SYMPTOMS TABLE
B
C
Disconnect the 2M driver side junction block assembly connector.
Disconnect the B5 fog light assembly LH connector.
Disconnect the B6 fog light assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2M-18 - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2M-19 - B5-2 (B) | Always | Below 1 Ω |
| 2M-19 or B5-2 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2M-19 - Battery negative (-) terminal | Battery not connected to 2M-18 and A-7 (FFGO) | Below 1 V |
| Battery positive (+) → 2M-18
Battery negative (-) → A-7 (FFGO) |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 2K and 2F driver side junction block assembly connectors.
Disconnect the B5 fog light assembly LH connector.
Disconnect the B6 fog light assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2K-1 - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2F-9 - B5-2 (B) | Always | Below 1 Ω |
| 2F-9 or B5-2 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2F-9 - Battery negative (-) terminal | Battery not connected to 2K-1, A-13 (FFGO) and A-14 (TRLY) | Below 1 V |
| Battery positive (+) → 2K-1
Battery negative (-) → A-13 (FFGO) and A-14 (TRLY) |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG